manualshive.com logo in svg

Cisco NM-1A-E3, User Manual, Page: 18 / 26

Share
Download
Cisco NM-1A-E3 User Manual Download Page 18

 

Configuring the Cisco NM-1A-T3/E3 Network Module

  Recommendations for Watermark Settings

18

Cisco IOS Release 12.4(15)T

Example of the Router Configuration Used for Watermark Testing

The following example provides the router configuration that was used for the watermark testing.

Table 2

Example of the Router Configuration Used for Watermark Testing

UUT1 (3845)

UUT2 (3845) 

class-map match-any COSQ_NBIP_LABS_TC1_COS4

match any 

 class-map match-any COSP_NBIP_LABS_TC1_COS4

match any 

 class-map match-any COSP_NBIP_LABS_TC1_EF

  match access-group name EF_APP_IPV4_TC1

 class-map match-any COSQ_NBIP_LABS_TC1_EF

  match access-group name EF_QUEUE_IPV4_TC1

 !

 !

 policy-map Child_Map3

  class COSP_NBIP_LABS_TC1_EF

    police cir 5000000 bc 625000

      conform-action set-dscp-transmit 46

      exceed-action drop 

 policy-map Child_Map2

  class COSP_NBIP_LABS_TC1_COS4

    police cir 5000000 bc 625000

      conform-action set-dscp-transmit 0

      exceed-action set-dscp-transmit 0

 policy-map Parent_Map1

  class COSQ_NBIP_LABS_TC1_EF

   priority 5000 625000

   service-policy Child_Map3

  class COSQ_NBIP_LABS_TC1_COS4

   bandwidth remaining percent 99

   random-detect dscp-based

   random-detect exponential-weighting-constant 1

   random-detect dscp 0   901   1200  10   

   service-policy Child_Map2

!  

interface GigabitEthernet0/0

 ip address 110.0.0.2 255.255.255.0

 load-interval 30 

 duplex auto 

 speed auto 

 media-type rj45 

!  

interface GigabitEthernet0/1

 ip address 20.0.0.1 255.0.0.0

 load-interval 30 

 duplex auto 

 speed auto 

 media-type rj45 

!  

class-map match-any COSQ_NBIP_LABS_TC1_COS4

match any

 class-map match-any COSP_NBIP_LABS_TC1_COS4

  match any   

 class-map match-any COSP_NBIP_LABS_TC1_EF

  match access-group name EF_APP_IPV4_TC1

 class-map match-any COSQ_NBIP_LABS_TC1_EF

  match access-group name EF_QUEUE_IPV4_TC1

 !            

 !   

 policy-map Child_Map3 

  class COSP_NBIP_LABS_TC1_EF

    police cir 5000000 bc 625000 

      conform-action set-dscp-transmit 46

      exceed-action drop  

 policy-map Child_Map2 

  class COSP_NBIP_LABS_TC1_COS4

    police cir 5000000 bc 625000 

      conform-action set-dscp-transmit 0

      exceed-action set-dscp-transmit 0

 policy-map Parent_Map1 

  class COSQ_NBIP_LABS_TC1_EF

   priority 5000 625000 

   service-policy Child_Map3 

  class COSQ_NBIP_LABS_TC1_COS4

   bandwidth remaining percent 99

   random-detect dscp-based 

   random-detect exponential-weighting-constant 1

   random-detect dscp 0   901   1200  10   

   service-policy Child_Map2 

!  

interface GigabitEthernet0/0 

  ip address 120.0.0.2 255.255.255.0

  load-interval 30  

  duplex auto  

  speed auto  

  media-type rj45  

 !   

 interface GigabitEthernet0/1 

  ip address 30.0.0.1 255.0.0.0 

  load-interval 30  

  duplex auto  

  speed auto  

  media-type rj45  

!  

Summary of Contents for NM-1A-E3



























Reviews:

No comments