Cisco Nexus 9396PX Hardware Installation Manual Download Page 23

Page: 23 / 74

C H A P T E R

Installing the Chassis

•

Installation Options with Rack-Mount Kits, Racks, and Cabinets, on page 13

•

Install a Rack, on page 14

•

Unpacking and Inspecting a New Switch, on page 14

•

Planning How to Position the Chassis in the Rack, on page 15

•

Installing the Chassis in a Two-Post Rack, on page 16

•

Installing the Chassis in a Four-Post Rack, on page 19

•

Grounding the Chassis, on page 23

•

Powering Up the Switch, on page 24

Installation Options with Rack-Mount Kits, Racks, and Cabinets

The rack-mount kit enables you to install the switch into racks of varying depths. You can position the switch
with easy access to either the port connections or the fan and power supply modules.

You can install the switch using the following rack-mount options:

• Rack-mount kit (NXK-ACC-RMK-2RU) which you can order from Cisco. This option offers you easy

installation, greater stability, increased weight capacity, added accessibility, and improved removability
with front and rear removal.

• Rack-mount kit (N9K-C9300-RMK) which you can order from Cisco.

You can install the switch in the following types of racks:

• Open EIA rack

• Perforated EIA cabinet

The rack or cabinet that you use must meet the requirements listed the in

General Requirements for Cabinets

and Racks, on page 45

section.

You are responsible for verifying that your rack and rack-mount hardware comply with the guidelines that
are described in this doc.

Note

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

Summary of Contents for Nexus 9396PX











































































Search results

Summary of Contents for Nexus 9396PX

Reviews:

Related manuals for Nexus 9396PX

Brands by name

Popular brands

Cisco Nexus 9396PX, Hardware Installation Manual

Search results

Summary of Contents for Nexus 9396PX

Reviews:

Related manuals for Nexus 9396PX

Brands by name

Popular brands