Cisco Nexus 9396PX Hardware Installation Manual Download Page 21 | Manualshive

Page: 21 / 74

background image

Width of the front clearance area (equal to the
width of the chassis with two rack-mount
brackets that are attached to it).

4

For the clearances required for a two-post rack installation, see the following figure.

Chassis width

3

Chassis

1

Service clearance that is required for replacing
the chassis (equals the length of the chassis).

4

Vertical rack-mount posts and rails

2

Both the front and rear of the chassis must be open to both aisles for airflow.

Note

Cisco Nexus 9396PX ACI-Mode Switch Hardware Installation Guide

11

Preparing the Site

Clearance Requirements

«
...
19
20
21
22
23
...
»

Summary of Contents for Nexus 9396PX











































































Reviews:

No comments

Related manuals for Nexus 9396PX

xStack DGS-3420 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 29

Brand: D-Link Pages: 454

Brand: D-Link Pages: 502

Brand: D-Link Pages: 244

Brand: D-Link Pages: 20

Brand: D-Link Pages: 2

Brand: D-Link Pages: 37

Brand: D-Link Pages: 28

Brand: Daxten Pages: 2

Brand: H3C Pages: 38

Brand: H3C Pages: 36

Brand: H3C Pages: 9

Brand: H3C Pages: 36

S12500X-AF Series

Brand: H3C Pages: 21

S12500X-AF Series

Brand: H3C Pages: 42

Brand: H3C Pages: 16

Brand: H-Tronic Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands