Cisco Nexus 2000 Series Installation Manual Download Page 186

Page: 186 / 190

F-8

Cisco Nexus 2000 Series Hardware Installation Guide

Appendix F Accessory Kit

Accessory Kit for Cisco Nexus 2248TP-E, 2224TP, 2232PP, 2248TP, 2232TM, and 2148T

Accessory Kit for Cisco Nexus 2248TP-E, 2224TP, 2232PP,
2248TP, 2232TM, and 2148T

Accessory kits for the Cisco Nexus 2148T, 2224TP, 2232PP, 2248TP, 2248TP-E, and 2232TM FEXs
contain the following items:

•

2 slider rails

•

2 rack-mount guides

•

2 rack-mount brackets

•

16 M4 x 0.7 x 8-mm Phillips countersunk screws

•

1 ground lug kit

•

1 ESD wrist strap

Table F-2

provides ordering information for the Cisco Nexus 2148T, 2224TP, 2232PP, 2248TP-ETP, and

2232TM FEXs.

Note

Additional parts can be ordered from your customer service representative.

Table F-2

Accessory Kit Information for the Cisco Nexus 2148T, 2224TP, 2232PP, 2248TP,
2248TP-E, and 2232TM Fabric Extenders

Accessory Kit

Details

N2K-C2148T-ACC

Cisco Nexus 2000 FEX 1GE accessory kit, spare

N2200-ACC-KIT

Cisco Nexus 2200 FEX accessory kit, spare

Summary of Contents for Nexus 2000 Series































































































































































































Search results

Summary of Contents for Nexus 2000 Series

Reviews:

Related manuals for Nexus 2000 Series

Brands by name

Popular brands

Cisco Nexus 2000 Series, Installation Manual

Search results

Summary of Contents for Nexus 2000 Series

Reviews:

Related manuals for Nexus 2000 Series

Brands by name

Popular brands