Cisco NC55A2-MOD-SE-H-S Manual Download Page 16 | Manualshive

Page: 16 / 24

background image

Figure 12: Installing the 40-Gigabit QSFP+ or 100-Gigabit QSFP28 Transceiver Module (Optical Transceiver Equipped with a Bail-Clasp Latch Shown)

Step 8

Press firmly on the front of the QSFP+ or QSFP28 transceiver module with your thumb to fully seat the transceiver in
the module’s transceiver socket (see the below figure).

If the latch is not fully engaged, you might accidentally disconnect the QSFP+ or QSFP28 transceiver module.

Caution

Connect Router to the Network

16

Connect Router to the Network

Installing the 40-Gigabit QSFP+ or 100-Gigabit Transceiver Module

«
...
14
15
16
17
18
...
»

Summary of Contents for NC55A2-MOD-SE-H-S

























Reviews:

No comments

Related manuals for NC55A2-MOD-SE-H-S

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Brand: Watchguard Pages: 24

Brand: Queclink Pages: 9

Brand: Klark Teknik Pages: 50

Brand: Qixiang Technology Pages: 16

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: Abocom Pages: 1

Brand: ZyXEL Communications Pages: 485

Brand: E-TOP Pages: 24

Brand: Intellinet Pages: 12

Octopus G Series

Brand: TwinMOS Pages: 29

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: ADIC Pages: 140

Brand: Lanpro Pages: 3

DGN2200M - Wireless-N 300 Router

Brand: NETGEAR Pages: 95

Brand: TP-Link Pages: 2

Brand: Fibrain Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands