Cisco N9K-C9332C Hardware Installation Manual Download Page 61

Page: 61 / 70

Photo

Cord Set Description

Part Number

HVDC

6.6-foot (2.0 m) cable with
Saf-D-Grid and three terminal
connectors

CAB-HVDC-3T-2M

Not applicable

All except Argentina, Brazil, and
Japan

No power cord included with
switch

NO-POWER-CORD

Table 2: HVAC/HVDC Power Cables Callout Table

Connect this end to the power supply unit.

DC Power Cable Specifications

Photo

Description

Part Number

The 1100W DC power supply
(NXA-PDC-1100W-PE/PI) is
shipped with a connector already
plugged into the power supply.

NXA-PDC-1100W-PE/PI

Regulatory Standards Compliance Specifications

The following table lists the regulatory standards compliance for the switch.

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

System Specifications

DC Power Cable Specifications

Summary of Contents for N9K-C9332C







































































Search results

Summary of Contents for N9K-C9332C

Reviews:

Related manuals for N9K-C9332C

Brands by name

Popular brands

Cisco N9K-C9332C, Hardware Installation Manual

Search results

Summary of Contents for N9K-C9332C

Reviews:

Related manuals for N9K-C9332C

Brands by name

Popular brands