Cisco N9K-C9332C Hardware Installation Manual Download Page 16 | Manualshive

Page: 16 / 70

background image

For

n

+1 redundancy, you can use one or two power sources for the two power supplies. For

n

+

n

redundancy,

you must use two power sources and connect each power supply to a separate power source.

Note

The power supplies are rated to output up to 1100 W, but the switch requires less than those amounts of power
from the power supply. To operate the switch, you must provision enough power from the power source to
cover the requirements of both the switch and a power supply. Typically, this switch and a power supply
require about 367 W of power input from the power source, but you must provision as much as 777 W power
input from the power source to cover peak demand.

Some of the power supply modules have rating capabilities that exceed the switch requirements. When
calculating your power requirements, use the switch requirements to determine the amount of power that is
required for the power supplies.

Note

To minimize the possibility of circuit failure, make sure that each power-source circuit that is used by the
switch is dedicated to the switch.

For AC input application, please refer to the following statement:

Note

Statement 1005—

Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the
protective devices are rated not greater than 20A (North America), 16A (Europe), and 13A (UK).

Warning

For DC input application, please refer to the following statement:

Note

Statement 1005—

Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent) protection.

• Ensure that the protective devices are rated not greater than 30A when the switch is powered with regular

DC power supplies (rated 48-60VDC).

• Ensure that the protective devices are rated not greater than 10A when the switch is powered with HVDC

power supplies (rated 240-350VDC).

Warning

Statement 1033

Connect the unit only to DC power source that complies with the Safety Extra-Low Voltage (SELV)
requirements in IEC 60950 based safety standards.

Warning

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

8

Preparing the Site

Planning for Power Requirements

«
...
14
15
16
17
18
...
»

Summary of Contents for N9K-C9332C







































































Reviews:

No comments

Related manuals for N9K-C9332C

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: CALIENT Pages: 46

Brand: CALIENT Pages: 42

Brand: Campbell Pages: 14

AVS-OCT-6448-210

Brand: AMX Pages: 1

IPS-800CE-D16, IPS-1600CE-D16

Brand: Western Telematic Pages: 58

Brand: Hama Pages: 56

Brand: FCI Pages: 78

Universal Videohub 288

Brand: Blackmagicdesign Pages: 107

Brand: SmartAVI Pages: 2

Brand: 3Com Pages: 62

DCRS-5200 Series

Brand: Digital China Networks Pages: 4

Brand: Conceptronic Pages: 28

Brand: Daewoo Pages: 7

Brand: ATEN Pages: 125

Brand: Linksys Pages: 3

Brand: Linkskey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands