Cisco MX200 G2 Administrator'S Manual Download Page 90

Page: 90 / 141

D15332.01 MX200 G2 and MX300 G2 Administrator Guide CE8.0, NOVEMBER 2015.

Cisco TelePresence MX200 G2 and MX300 G2

Administrator Guide

NetworkServices WelcomeText

Choose which information the user should see when logging on to the codec through

Telnet/SSH.

Requires user role: ADMIN
Default value: On

Value space: Off/On

Off: The welcome text is: Login successful
On: The welcome text is: Welcome to <system name>; Software version; Software

release date; Login successful.

NetworkServices XMLAPI Mode

Enable or disable the video system's XML API. For security reasons this may be disabled.

Disabling the XML API will limit the remote manageability with for example TMS, which no

longer will be able to connect to the video system.

Requires user role: ADMIN
Default value: On

Value space: Off/On

Off: The XML API is disabled.
On: The XML API is enabled (default).

Introduction

Configuration

Peripherals

Maintenance

System settings

Appendices



System settings

Summary of Contents for MX200 G2














































































































































Search results

Summary of Contents for MX200 G2

Reviews:

Brands by name

Popular brands

Cisco MX200 G2, Administrator'S Manual

Search results

Summary of Contents for MX200 G2

Reviews:

Brands by name

Popular brands