Cisco Firepower 9300 Hardware Installation Manual Download Page 78

Page: 78 / 80

Figure 53: HVDC Power Feeds

Power feed for PSU-1

Power feed for PSU-2

Step 5

Set the HVDC disconnect switch in the circuit to ON.

In a system with multiple power supplies, connect each power supply to a separate HVDC power source. In
the event of a power source failure, if the second source is still available, it can maintain system operation.

Caution

Step 6

Verify power supply operation by checking the power supply LED on the front of the chassis.

See

Power Supply Modules, on page 24

for the LED values.

Remove and Replace the Fan Module

You can remove and replace fan modules while the system is running. The airflow moves from front to back.
See

Fan Modules, on page 26

for more information about the fan module.

Cisco Firepower 9300 Hardware Installation Guide

Maintenance and Upgrade

Remove and Replace the Fan Module

Summary of Contents for Firepower 9300

















































































Search results

Summary of Contents for Firepower 9300

Reviews:

Brands by name

Popular brands

Cisco Firepower 9300, Hardware Installation Manual

Search results

Summary of Contents for Firepower 9300

Reviews:

Brands by name

Popular brands