manualshive.com logo in svg

Cisco Firepower 9300, Hardware Installation Manual

Share
Download
Cisco Firepower 9300 Hardware Installation Manual Download Page 30

Fan Modules

The Firepower 9300 requires four fan modules, which are hot-swappable. They are installed in the rear of the
chassis. When you remove a fan module, make sure you replace it quickly to avoid overheating the system.

The fan modules are numbered left to right, for example, FAN-1, FAN-2, FAN-3, and FAN-4.

The fan modules have the following LEDs:

• Amber, flashing—Fan failure.

• Green—Fan running normally.

For More Information

See

Remove and Replace the Fan Module, on page 74

for the procedure for removing and replacing fan

modules.

Supported SFP/SFP+ and QSFP Transceivers

The SFP/SFP+ and QSFP transceivers are bidirectional devices with a transmitter and receiver in the same
physical package. They are a hot-swappable optical or electrical (copper) interface that plugs into the
SFP/SFP+/QSFP ports on the fixed ports and the network module ports, and provides Ethernet connectivity.

Use appropriate ESD procedures when inserting the transceiver. Avoid touching the contacts at the rear, and
keep the contacts and ports free of dust and dirt. Keep unused transceivers in the ESD packing that they were
shipped in. The following figure shows a sample SFP transceiver.

Warning

Figure 16: SFP

Bail clasp

2

Dust plug

1

Transmit optical bore

4

Receive optical bore

3

Cisco Firepower 9300 Hardware Installation Guide

26

Overview

Fan Modules

Summary of Contents for Firepower 9300

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands