background image

1-8

Cisco FlexWAN and Enhanced FlexWAN Modules Installation Guide

OL-8357-01

Chapter 1      Installing the FlexWAN and Enhanced FlexWAN Modules

  Installing a FlexWAN or Enhanced FlexWAN Module Port Adapter

Installing a New Port Adapter in an Enhanced FlexWAN Module

This section describes how to first remove a port adapter from an Enhanced FlexWAN module, then how 
to install a new port adapter into its bay. (The procedure for the FlexWAN module is similar.)

Note: You must first remove the 
Enhanced FlexWAN Module from 
the chassis before removing a port 
adapter from the Enhanced 
FlexWAN Module.

Step 2

With the screw removed, grasp the 
handle on the front of the
port adapter (or blank port adapter) 
and carefully pull it out of its bay, 
away from the edge connector at 
the rear of the bay. (See A.)

Step 3

To install the port adapter, carefully 
align the port adapter carrier 
between the upper and the lower 
edges of the port adapter bay.
(See B.)

Step 5

Install the screw in the rear of the 
port adapter bay. Do not overtighten 
the screw. (See A.)

Step 6

Reinstall the Enhanced FlexWAN 
Module in the chassis, and tighten 
the captive installation screw on each 
side of the Enhanced FlexWAN 
Module faceplate. (See C.)

96929

B

A

C

Step 1

To remove the port adapter,
remove the screw that
secures the port adapter (or
blank port adapter). (See A.)

Step 4

Carefully slide the new
port adapter into the port adapter 
bay until the connector on the
port adapter is completely seated in 
the connector at the rear of the
port adapter slot. (See B.)

Slot

guide

Screw

FAN
LED

2

3

4

5

6

7

8

9

SUPERVISOR I

STATUS SYSTEMACTIVE PW

R MGMT

RESET

CONSOLE

1%

PCMCIA

EJECT

LINK

LINK

SUPERVISOR I

WS-X6K-SUP1

STATUS SYSTEMACTIVE PWR MGMT

RESET

CONSOLE

Switch    Load   

100%

1%

DTE/
   DCE

PCMCIA

EJECT

PORT 1

LINK

PORT 2

LINK

8 PORT GIGABIT ETHERNET

WS-X6408

1

LIN

K

ST

AT

US

2

3

4

5

6

7

8

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

8 PORT GIGABIT ETHERNET

WS-X6408

1

LIN

K

ST

AT

US

2

3

4

5

6

7

8

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

8 PORT GIGABIT ETHERNET

WS-X6408

1

LIN

K

ST

AT

US

2

3

4

5

6

7

8

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

LIN

K

24 PORT 100FX

WS-X6224

STA

TU

S

24 PORT 100FX

WS-X6224

ST

AT

US

24 PORT 100FX

WS-X6224

STA

TU

S

1

LINK

2

LINK

3

LINK

4

LINK

5

LIN

K

6

LINK

7

LINK

8

LINK

9

LIN

K

10

LINK

11

LINK

12

LIN

K

13

LINK

14

LINK

15

LINK

16

LIN

K

17

LINK

18

LINK

19

LINK

20

LINK

21

LINK

22

LINK

23

LINK

24

LINK

1

LIN

K

2

LIN

K

3

LINK

4

LINK

5

LIN

K

6

LINK

7

LINK

8

LINK

9

LIN

K

10

LINK

11

LINK

12

LINK

13

LINK

14

LINK

15

LINK

16

LIN

K

17

LINK

18

LINK

19

LINK

20

LIN

K

21

LINK

22

LINK

23

LINK

24

LINK

1

LINK

2

LINK

3

LINK

4

LINK

5

LINK

6

LINK

7

LINK

8

LINK

9

LINK

10

LINK

11

LINK

12

LINK

13

LINK

14

LINK

15

LINK

16

LINK

17

LINK

18

LINK

19

LINK

20

LINK

21

LINK

22

LINK

23

LINK

24

LINK

ST

AT

US

Summary of Contents for Enhanced FlexWAN











Reviews: