background image

 

11

Configuring Gigabit Ethernet Enhanced High-Speed WAN Interface Cards

OL-24318-02

  Configuration Examples for EHWIC 1 GE-SFP-CU

Fragment Frames Received : 0

In-Range Length Errors : 0

Alignment Errors Received : 0

Symbol Errors Received : 0

Internal MAC Errors : 0

EHWIC-1GE-SFP Mac Tx Statistics:

=============================================

Bytes Transmitted : 2997

Frames Transmitted OK : 22

Broadcast Frames Transmitted OK : 2

Multicast Frames Transmitted OK : 20

Underrun Error : 0

Control Frames Transmitted OK : 4

64 byte Frames Transmitted OK : 6

65-127 byte Frames Transmitted OK : 13

128-255 byte Frames Transmitted OK : 0

256-511 byte Frames Transmitted OK : 3

512-1023 byte Frames Transmitted OK : 0

1024-Max_Frame_Size byte Frames Transmitted OK : 0

VLAN Frames Transmitted OK : 0

PAUSE Frames Transmitted OK : 4

Oversized Frames Transmitted OK : 0

Single Collision Frames : 0

Multiple Collision Frames : 0

Deferred Frames : 0

Late Collision Frames : 0

Frames Aborted due to Excessive Collisions : 0

Carrier Sense Errors : 0

******* HWIC Common Registers at 10000000 *******

HWIC ID: 0x2

HWIC Revision: 0x0

HWIC Status: 0x0

HWIC DDR TXCRC:0x0

HWIC Control: 0xC080

DDR Enable 1 Software Reset 1

Interrupt Module Reset 0 GDF Module Reset 0

DMA Module Reset 0 Flow Control Reset 0

IRQ2 Global Int Mask 1 IRQ1 Global Int Mask 0

DDR TXCRC Int Mask 0 DDR TXClk Loss Int Mask 0

TX Fifo Overrun Int Mask 0

HWIC Interrupt Event: 0x0

DDR TXCRC Int 0 DDR TXClk Loss Int 0

TX Fifo Overrun Int 0

HWIC Diag 1: 0x0

HWIC Diag 2: 0x1C0F

******* HWIC Host Registers at 10FE0000 *******

Status (0x00):

Card Present Low 0 Graceful Stop Tx Complete 0

Config (0x00007322):

Hwic Reset 0 Hwic Host Reset 0

Hwic IRQ2 Type Net Hwic IRQ1 Type unknown

Rx Queue Watermark Enable 0 Auto XOFF When Full 0

Rx Int On Last 1 Graceful Stop Tx 0

Generic Rx Enable 0 Generic Tx Enable 0

DDR Enable 1 Loopback 0

Error Interrupt Enable (0x34DFF):

Rx Done Error Int 1 Card Present Change Int 1

Hwic Int Frame Error Int 0x04 Tx First Last Error Int 1

Tx Done Error Int 1 IRQ2 Int 0

IRQ1 Int 1 Host Specific Error Int 1

Rx Overrun Int 1 DDR RxClk Missing Int 1

Reg RW Timeout Int 1 Reg RW Error Int 1

Rx CRC Int 1 Rx Format Error Int 1

DMA Error Int 1

Summary of Contents for EHWIC 1 GE-SFP-CU



















Reviews: