Cisco CiscoWorks WLSE 1130-19 Installation And Configuration Manual Download Page 74

Page: 74 / 104

Chapter 3 Setting Up the WLSE

Logging into the Web Interface and Verifying Connectivity

3-12

Installation and Configuration Guide for the CiscoWorks Wireless LAN Solution Engine

78-16778-01

Logging into the Web Interface and Verifying
Connectivity

Note

Disable pop-up blocker software while using the WLSE web interface.

To verify HTTP and HTTPS connectivity, connect to the WLSE using a
supported, properly configured Web browser and perform the following steps:

Step 1

To verify HTTP connectivity, enter the system IP address, followed by

:1741

(the

default port number).

For example, if the system IP address is 209.165.202.128, enter

http://209.165.202.128:1741

If a login dialog box appears, you have connectivity.

Step 2

To verify HTTPS connectivity, enter the system IP address, prefixed by https.
Do not use a port number in the URL.

For example, if the system IP address is 209.165.202.128, enter

https://209.165.202.128

If a login dialog box appears, you have connectivity.

Step 3

Enter the user name

admin

and the password you created during setup in the login

dialog box. The WLSE home page appears.

Summary of Contents for CiscoWorks WLSE 1130-19









































































































Search results

Summary of Contents for CiscoWorks WLSE 1130-19

Reviews:

Related manuals for CiscoWorks WLSE 1130-19

Brands by name

Popular brands

Cisco CiscoWorks WLSE 1130-19, Installation And Configuration Manual

Search results

Summary of Contents for CiscoWorks WLSE 1130-19

Reviews:

Related manuals for CiscoWorks WLSE 1130-19

Brands by name

Popular brands