manualshive.com logo in svg

Cisco Catalyst 6816-X-LE, Hardware Installation Manual

Share
Download
Cisco Catalyst 6816-X-LE Hardware Installation Manual Download Page 89

A P P E N D I X

C

Repacking the Switch

If you need to return or move the switch chassis, follow these steps to repack the switch using the original
packaging material.

Procedure

Step 1

Set the chassis in the bottom pallet.

Figure 39: Packing Material

Step 2

Place the packing bag over the chassis.

Step 3

Place the front-packing material and power supply packing material around the chassis.

Step 4

Place the power supplies in the spaces provided in the power supply packing material.

Step 5

Place the top-packing material over the top of the chassis and power supplies.

Step 6

Place the rack-mount kit and the accessory kit on the top-packing material.

You must include the accessory kit for the final packaging to fit properly.

Note

Step 7

Place the outside carton over the entire package.

Step 8

Fold the outside carton down over the top and seal with packing tape.

Catalyst 6840-X Switch Series Hardware Installation Guide

77

Summary of Contents for Catalyst 6816-X-LE





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands