Cisco Catalyst 6816-X-LE Hardware Installation Manual Download Page 53

Page: 53 / 100

Figure 16: Installing the chassis on a Rack with a 17.5 in. (44.45 cm) Opening

Installing the L Brackets on a Rack with 17.75 in. (45.09 cm) Opening

Procedure

Step 1

Attach the L bracket to the chassis as shown in the following figure.

Figure 17: Attaching the L Bracket to the chassis

Step 2

Position the chassis in the rack and align the mounting holes in the L bracket with the mounting holes in the
equipment rack.

Step 3

Secure the chassis using four screws through the holes in the L bracket and into the rack post holes.

Catalyst 6840-X Switch Series Hardware Installation Guide

Installing the Switch

Installing the L Brackets on a Rack with 17.75 in. (45.09 cm) Opening

Summary of Contents for Catalyst 6816-X-LE





































































































Search results

Summary of Contents for Catalyst 6816-X-LE

Reviews:

Related manuals for Catalyst 6816-X-LE

Brands by name

Popular brands

Cisco Catalyst 6816-X-LE, Hardware Installation Manual

Search results

Summary of Contents for Catalyst 6816-X-LE

Reviews:

Related manuals for Catalyst 6816-X-LE

Brands by name

Popular brands