manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 545

 

11-17

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 11      Statistics Troubleshooting

Troubleshooting Statistics Alarms

Troubleshooting Statistics Alarms

This section provides the information needed to monitor and correct statistics alarms. 

Table 11-3

 lists all 

of the statistics alarms in numerical order and provides cross reference to each subsection in this section.

Measurement Handshake Error–Schema Inconsistency—Statistics (12)

The Measurement Handshake Error–Schema Inconsistency alarm (major) indicates that a measurement 
handshake error has occurred. The primary cause of the alarm is that counters have been added or deleted 
from the schema in Oracle but not in the Call Agent. To correct the primary cause of the alarm, add or 
delete the counters on the CA. The secondary cause of the alarm is that the software load has been 
installed incorrectly. To correct the secondary cause of the alarm, re-install the software load.

Traffic and Measurements Module Application Programming Interface 
Failure—Statistics (13)

The Traffic and Measurements Module Application Programming Interface Failure alarm (major) 
indicates that the TMM API failed. The primary cause of the alarm is that the system is unable to 
initialize the shared memory. To correct the primary cause of the alarm, reconfigure and restart the 
system. The secondary cause of the alarm is that a process is unable to attach to the shared memory. To 
correct the secondary cause of the alarm, restart the offending process. The ternary cause of the alarm is 
that the shared memory table has overflown. To correct the ternary cause of the alarm, 
reconfigure/restart or fix problematic application. The subsequent cause of the alarm is that the shared 
memory is exhausted. To correct the subsequent cause of the alarm, reconfigure and restart the system.

Threshold Crossing Alert—Statistics (15)

The Threshold Crossing Alert alarm (minor) indicates that a threshold crossing has occurred. To correct 
the cause of the alarm, reduce the provisioning workload.

Table 11-3

BTS 10200 Statistics Alarms 

Alarm Type

Alarm Name

Alarm Severity

STATISTICS(12)

Measurement Handshake Error–Schema Inconsistency—Statistics (12)

MAJOR

STATISTICS(13)

Traffic and Measurements Module Application Programming Interface 
Failure—Statistics (13)

MAJOR

STATISTICS(15)

Threshold Crossing Alert—Statistics (15)

MINOR

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands