manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 540

 

11-12

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 11      Statistics Troubleshooting

Monitoring Statistics Events

Monitoring Statistics Events

This section provides the information needed to monitor and correct statistics events. 

Table 11-2

 lists all 

of the statistics events in numerical order and provides cross reference to each subsection in this section.

Test Report—Statistics (1)

The Test Report event is for testing the statistics event category. The event is informational and no 
further action is required.

Call Agent Measurement Collection Started—Statistics (2)

The Call Agent Measurement Collection Started event functions as an informational alert that the call 
agent measurement collection has started. The event is informational and no further action is required.

Table 11-2

BTS 10200 Statistics Events 

Event Type

Event Name

Event Severity

STATISTICS(1)

Test Report—Statistics (1)

INFO

STATISTICS(2)

Call Agent Measurement Collection Started—Statistics (2)

INFO

STATISTICS(3)

Call Agent Measurement Collection Finished—Statistics (3)

INFO

STATISTICS(4)

Plain Old Telephone Service/Centrex/Telecommunications Data Link Monitor 
Feature Server Measurement Collection Started—Statistics (4)

INFO

STATISTICS(5)

Plain Old Telephone Service/Centrex/Telecommunications Data Link Monitor 
Feature Server Measurement Collection Finished—Statistics (5)

INFO

STATISTICS(6)

Advanced Intelligent Network Feature Server Measurement Collection 
Started—Statistics (6)

INFO

STATISTICS(7)

Advanced Intelligent Network Feature Server Measurement Collection 
Finished—Statistics (7)

INFO

STATISTICS(8)

Message Send Failure—Statistics (8)

WARNING

STATISTICS(9)

Measurement Table Structured Query Language Read Error—Statistics (9)

WARNING

STATISTICS(10)

Measurement Table Structured Query Language Write Error—Statistics (10)

WARNING

STATISTICS(11)

Measurement Collection Application Programming Interface Failure—Statistics (11)

WARNING

STATISTICS(12)

Measurement Handshake Error–Schema Inconsistency—Statistics (12)

MAJOR

STATISTICS(13)

Traffic and Measurements Module Application Programming Interface 
Failure—Statistics (13)

MAJOR

STATISTICS(14)

MDII Trunk—Statistics (14)

WARNING

STATISTICS(15)

Threshold Crossing Alert—Statistics (15)

MINOR

STATISTICS(16)

Trunk Group has Reached the MDII Alarm Threshold—Statistics (16)

WARNING

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands