manualshive.com logo in svg

Cisco ATA 190, Administration Manual

Share
Download
Cisco ATA 190 Administration Manual Download Page 18

 

1-8

Cisco ATA 190 Analog Telephone Adaptor Administration Guide for SIP (Version 1.0)

OL-31821-01

Chapter 1      Cisco ATA 190 Analog Telephone Adapter Overview

Installation and Configuration Overview

  •

REFER

  •

INVITE

  •

BYE

  •

CANCEL

  •

NOTIFY

  •

OPTIONS

  •

ACK

  •

SUBSCRIBE

Supplementary Services

SIP supplementary services are services that you can use to enhance your phone service. For information 
on how to use these services, see 

Chapter 6, “Using SIP Supplementary Services”.

The ATA 190 supports these SIP supplementary services:

  •

Caller ID

  •

Call-waiting caller ID

  •

Voice mail indication

  •

Making a conference call

  •

Call waiting

  •

Call forwarding

  •

Calling-line identification

  •

Unattended transfer (blind transfer)

  •

Attended transfer

  •

Shared Line

  •

SpeedDial

  •

Conference (MeetMe)

  •

Pick Up

  •

Redial

Installation and Configuration Overview

Table 1-1

 provides the basic steps required to install and configure the ATA 190 to make it operational 

in a typical SIP environment where a large number of ATA 190s must be deployed.

Summary of Contents for ATA 190















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands