Cisco ASR 14000 Series Installation Manual Download Page 65 | Manualshive

Page: 65 / 132

background image

4-13

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 4 Installing and Removing MSCs, PLIMs, and Associated Components

How to Install or Remove a Slot Cover

Figure 4-11

Cable Management Bracket

How to Install or Remove a Slot Cover

This section contains the following procedures:

•

Installing a Slot Cover

•

Removing a Slot Cover

Installing a Slot Cover

This section describes how to install a slot cover in the Cisco ASR 14000 series 8-slot line card chassis.
The chassis is shipped with slot covers over the switch fabric card and RP card slots; we advise installing
slot covers over any empty slots in the chassis. Both slot cover types are installed in the same manner.
(

shows a switch fabric slot cover for reference.) For more detailed information on the slot

covers, see the

“Information About Impedance Carriers and Slot Covers” section on page 4-6

101818

«
...
63
64
65
66
67
...
»

Summary of Contents for ASR 14000 Series





































































































































Reviews:

No comments

Related manuals for ASR 14000 Series

Brand: GE Pages: 4

Brand: Magnat Audio Pages: 2

Brand: Patton electronics Pages: 2

ipRocketLink 3086FR

Brand: Patton electronics Pages: 6

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: XAVI Technologies Corp. Pages: 71

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Usr Pages: 2

totalstorage 200

Brand: IBM Pages: 152

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Brand: Teknim Pages: 10

Brand: TP-Link Pages: 2

Brand: Westermo Pages: 34

Brand: NETGEAR Pages: 152

TEG-S16R - DATA SHEETS

Brand: TRENDnet Pages: 12

Brand: Infoblox Pages: 44

Brand: M86 Security Pages: 540

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands