background image

13

Step 3

Configure to a fixed speed through the command-line interface (CLI) commands.

Connect the Shared Port Adapter Cables

The instructions for connecting the cables for the shared port adapters installed in the Cisco ASR 1002 Router are contained in 
the 

Cisco ASR 1000 Series Aggregation Services Routers SPA and SIP Hardware Installation Guide

.

Install the Cables Using the Cable-Management Bracket

Cables coming off the front side of the Cisco ASR 1002 integrated route processor and SPAs utilize the chassis level 
cable-management brackets provided on the chassis rack-mount brackets (see 

Figure 10

).

Figure 10

Cisco ASR 1002 Integrated Route Processor Cable-Management 

To secure shared port adapter interface cables and input or output cables connected to the Cisco ASR 1002 Router, follow these 
steps:

Step 1

When installing the network interface cables, route the cables up to and through the cable-management bracket ‘U’ 
device. If you are using very thin cables that slip through the bracket openings, insert nylon cable ties through the holes 
in the bracket and wrap them around the cables to secure them.

Step 2

Route the excess cable out through either end of the bracket, coil it, and secure it to the rack using nylon cable ties or 
some other mode of attachment.

Step 3

It might be necessary to bundle longer cables to avoid tangling them. Do this at the cable-management bracket or at 
the rack, but leave enough slack in the cables to remove a Cisco ASR 1000-ESP5 and change cables as required. Also, 
do not block the power supply air vents with cables.

This completes the procedure for installing the cables in the cable-management bracket.

1

BITS cable 

4

AUX cable

2

MGMT cable

5

Cable-management U feature device

3

CON cable

ASR 100

2

stat

pwr

min

maj

crit

SPA-4XOC3

-POS

S

TA

T

U

S

0

1

2

3

C

/A

A/L

C

/A

A

/L

C

/A

A/L

C

/A

A

/L

SPA-4XOC

3-POS

S

T

A

T

U

S

0

1

2

3

C

/A

A

/L

C

/A

A

/L

C/A

A

/L

C

/A

A

/L

STAT

QE0

QE1

QE2

QE3

BOOT

CARRIE

R

LINK

PWR ST

AT

MTS

MGMT

AUX

CON

SPA-4XOC

3-POS

S

T

A

T

U

S

0

1

2

3

C

/A

A

/L

C

/A

A

/L

C

/A

A

/L

C/A

A

/L

280287

5

5

1

2

3

4

Summary of Contents for ASR 1002





































Reviews: