Cisco ASA 5508-X Configuration Manual Download | Manualshive

Page: 332 / 428

background image

14-12

Cisco ASA Series Firewall CLI Configuration Guide

Chapter 14 Inspection for Voice and Video Protocols

MGCP Inspection

Monitoring H.323 RAS Sessions

The

show h323 ras

command displays connection information for H.323 RAS sessions established

across the ASA between a gatekeeper and its H.323 endpoint. Along with the

debug h323 ras event

and

show local-host

commands, this command is used for troubleshooting H.323 RAS inspection engine

issues.

The following is sample output from the

show h323 ras

command:

hostname#

show h323 ras

Total: 1

GK Caller

172.30.254.214 10.130.56.14

This output shows that there is one active registration between the gatekeeper 172.30.254.214 and its
client 10.130.56.14.

MGCP Inspection

The following sections describe MGCP application inspection.

•

MGCP Inspection Overview, page 14-12

•

Configure MGCP Inspection, page 14-13

•

Configuring MGCP Timeout Values, page 14-16

•

Verifying and Monitoring MGCP Inspection, page 14-16

MGCP Inspection Overview

MGCP is a master/slave protocol used to control media gateways from external call control elements
called media gateway controllers or call agents. A media gateway is typically a network element that
provides conversion between the audio signals carried on telephone circuits and data packets carried over
the Internet or over other packet networks. Using NAT and PAT with MGCP lets you support a large
number of devices on an internal network with a limited set of external (global) addresses. Examples of
media gateways are:

•

Trunking gateways, that interface between the telephone network and a Voice over IP network. Such
gateways typically manage a large number of digital circuits.

•

Residential gateways, that provide a traditional analog (RJ11) interface to a Voice over IP network.
Examples of residential gateways include cable modem/cable set-top boxes, xDSL devices,
broad-band wireless devices.

•

Business gateways, that provide a traditional digital PBX interface or an integrated soft PBX
interface to a Voice over IP network.

MGCP messages are transmitted over UDP. A response is sent back to the source address (IP address
and UDP port number) of the command, but the response may not arrive from the same address as the
command was sent to. This can happen when multiple call agents are being used in a failover
configuration and the call agent that received the command has passed control to a backup call agent,
which then sends the response. The following figure illustrates how you can use NAT with MGCP.

«
...
330
331
332
333
334
...
»

Summary of Contents for ASA 5508-X













































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASA 5508-X

Pro VersaChassis Mini

Brand: Vex Robotics Pages: 45

Brand: HPE Pages: 4

Brand: ERECA Pages: 19

Brand: National Instruments Pages: 64

Brand: National Instruments Pages: 12

Brand: Magma Pages: 40

1U Rackmount Chassis Kit R10-A2P4

Brand: Asus Pages: 34

Brand: DEV Pages: 143

TelePresence Server 7010

Brand: Cisco Pages: 204

TelePresence Server 7010

Brand: Cisco Pages: 287

CRS-1 - Carrier Routing System Router

Brand: Cisco Pages: 436

VelocityKVM T-4200 Series

Brand: Thinklogical Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands