background image

OL-30194-01 

 

Important Safety Instructions,

 Continued 

 

Covers

 - Do not open the cover of this equipment and attempt service unless 

instructed to do so in the instructions. Refer all servicing to qualified service 
personnel only. 

 

Moisture

 - Do not allow moisture to enter this equipment. 

 

Cleaning

 - Use a damp cloth for cleaning. 

 

Safety Checks

 - After service, assemble this equipment and perform safety checks 

to ensure it is safe to use before putting it back into operation. 

 

Electrostatic Discharge 

Electrostatic discharge (ESD) results from the static electricity buildup on the human 
body and other objects. This static discharge can degrade components and cause 
failures. 

Take the following precautions against electrostatic discharge: 

 

Use an anti-static bench mat and a wrist strap or ankle strap designed to safely 
ground ESD potentials through a resistive element. 

 

Keep components in their anti-static packaging until installed. 

 

Avoid touching electronic components when installing a module. 

 

Fuse Replacement 

To replace a fuse, comply with the following: 

 

Disconnect the power before changing fuses. 

 

Identify and clear the condition that caused the original fuse failure. 

 

Always use a fuse of the correct type and rating. The correct type and rating are 
indicated on this equipment. 

 
 

Modifications 

This equipment has been designed and tested to comply with applicable safety and 
EMC regulations, codes, and standards to ensure safe operation in its intended 
environment. Refer to this equipment's data sheet for details about regulatory 
compliance approvals. 

Do not make modifications to this equipment. Any changes or modifications could 
void the user’s authority to operate this equipment. 

Modifications have the potential to degrade the level of protection built into this 
equipment, putting people and property at risk of injury or damage. Those persons 
making any modifications expose themselves to the penalties arising from proven 
non-compliance with regulatory requirements and to civil litigation for 
compensation in respect of consequential damages or injury. 

 

Continued on next page 

Summary of Contents for 93250













Reviews: