manualshive.com logo in svg

Cisco 9300-EX, Hardware Installation Manual

Share
Download
Cisco 9300-EX Hardware Installation Manual Download Page 12

All fan modules and power supplies must use the same airflow direction during
operations. If you are using the 1200-W HVAC/HVDC power supply, the power supply
automatically uses the same airflow direction as used by the other modules in the switch.

Note

The following figure shows the hardware features seen from the port side of the chassis.

Screw holes (6) for attaching
rack mounting brackets

4

Chassis LEDs (Beacon [BCN], Status [STS], and Environment
[ENV])

1

Screw holes (2) for attaching
grounding lug

5

48 10/25-Gigabit SFP+ ports to APICs

2

6 40/100-Gigabit QSFP28 optical ports for uplink connections
to spine switches

3

To determine which transceivers, adapters, and cables are supported by this switch, see the

Cisco Transceiver

Modules Compatibility Information

document.

The following figure shows the hardware features seen from the power supply side of the chassis.

Out-of-band management port (SFP port)

6

Two power supplies (one used for operations and
one used for redundancy) (AC power supplies
shown) with power supply slot 1 on the left and
slot 2 on the right.

1

USB port used for saving or copying functions

7

Four fan modules with fan slot 1 on the left and
fan slot 4 on the right

2

   Cisco Nexus 93180YC-EX ACI Mode Hardware Installation Guide

2

Overview

Overview

Summary of Contents for 9300-EX











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands