Cisco 850 Series Hardware Installation Manual Download Page 79

Page: 79 / 92

6-3

Cisco 850 Series and Cisco 870 Series Access Routers Hardware Installation Guide

OL-5331-01

Chapter 6 Troubleshooting

Problems After the Router Is Running

Table 6-2

lists problems that could occur after the router has been up and running.

No connection to
xDSL link. (The WAN
LNK LED on the front
panel is off for a long
time.)

Improperly connected cable.

•

Make sure that you have connected the ADSL cable properly.
See

Chapter 4, “Router Cabling Procedures.”

•

Make sure that the connectors at both ends of the cable are
securely seated.

No connection to
xDSL link. (The CD
LED on the front panel
is off for a long time.)

Wrong cable.

•

Make sure that you are using the correct cable. See

Appendix A,

“Specifications.”

No connection to
xDSL link. (The CD
LED on the front panel
is off for a long time.)

Improperly connected cable.

•

Make sure that you have connected the ADSL cable properly.
See

Chapter 4, “Router Cabling Procedures.”

•

Make sure that the ADSL port is connected to the correct port on
the ISDN splitter.

•

Make sure that the connectors at both ends of the cable are
securely seated.

Table 6-1

Problems During First Startup (continued)

Symptom

Problem

Solutions

Table 6-2

Problems After the Router Is Running

Symptom

Problem

Solutions

Problems with Ethernet connection.
(ETHERNET LAN 0, ETHERNET
LAN 1, ETHERNET LAN 2, and
ETHERNET LAN 3 LEDs are off.)

A cable-related problem:

•

Disconnected cable.

•

Damaged cable.

Perform the following tasks in order:

Make sure that the connectors at both ends of the
cable are secure.

Check whether the cable is physically damaged.
If it is damaged, order another cable from
Cisco Systems, or replace it with a similar cable.

Connection to the broadband or
Ethernet line is intermittent or lost.
(The WAN LNK, ADSL CD, or
G.SHDSL CD LED on the front panel
is off.)

A cable-related problem:

•

Disconnected cable.

•

Damaged cable.

Perform the following tasks in order:

Make sure that the connectors at both ends of the
cable are secure.

Make sure that the cable is not physically
damaged. If it is damaged, order another cable
from Cisco Systems, or replace it with a similar
cable.

Connection to the broadband or
Ethernet line is intermittent or lost.
(The WAN LNK, ADSL CD, or
G.SHDSL CD LED on the front panel
is off.)

Problem with broadband line
or WAN service.

Contact your broadband line or WAN service provider
to determine whether there is a problem.

Summary of Contents for 850 Series





























































































Search results

Summary of Contents for 850 Series

Reviews:

Related manuals for 850 Series

Brands by name

Popular brands

Cisco 850 Series, Hardware Installation Manual

Search results

Summary of Contents for 850 Series

Reviews:

Related manuals for 850 Series

Brands by name

Popular brands