Cisco 2431 - IAD Router Software Configuration Manual Download Page 48

Page: 48 / 124

3-14

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 3 Configuring with the Command-Line Interface

Configuring T1/E1 Interfaces

Configuring DS0 Groups for CAS

The Cisco IAD2430 IAD supports as many as 24 voice lines (DS0s) for CAS, with

controller:DS0-group

identification of 1:0 through 1:23.

Perform the following steps to configure the basic T1 controller and digital voice port settings.

SUMMARY STEPS

enable

configure terminal

controller t1/e1

slot/port

mode css

ds0-group

ds0-group-number

timeslots

timeslot-number

voice-port

slot/port ds0-group-no

dial-type {pulse|dtmf}

compand-type {u-law|a-law}

no shutdown

10.

exit

11.

Ctrl-z

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Example:

Router# enable

Enters privileged EXEC mode.

Step 2

configure terminal

Example:

Router# configure terminal

Enters global configuration mode.

Step 3

controller t1/e1

slot/port

Example:

Router(config)# controller t1 0/2

Enters controller configuration mode for controller 1 (the
trunk controller for the T1-PBX port).

Note

DS0-group number should be different from
channel-group number and TDM-group number
under the same controller.

Step 4

mode css

Example:

Router(config-controller)# mode css

Enters CAS configuration mode and configures the
T1/E1 trunk to support signaling that matches the PBX
signaling type:

•

cas

—Channel-associated signaling

•

Common channel signaling cross-connect

—CCS

cross-connect for bearer channels

•

ccs frame-forwarding

—CCS transparent signaling

Summary of Contents for 2431 - IAD Router





























































































































Search results

Summary of Contents for 2431 - IAD Router

Reviews:

Related manuals for 2431 - IAD Router

Brands by name

Popular brands

Cisco 2431 - IAD Router, Software Configuration Manual

Search results

Summary of Contents for 2431 - IAD Router

Reviews:

Related manuals for 2431 - IAD Router

Brands by name

Popular brands