Cisco 2431 - IAD Router Software Configuration Manual Download Page 30

Page: 30 / 124

2-10

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 2 Using the setup Command Facility

Configuring Controller and Interface Parameters

T1 is capable of being configured for channel 1-24

Enter number of time slots [24]: 3

Configure more channel groups? [no]: y

Enter number of time slots [21]: 3

Configure more channel groups? [no]: y

Enter number of time slots [18]: 3

Configure more channel groups? [no]: y

Enter number of time slots [15]:

Configure more channel groups? [no]:

The

“PPP Encapsulation” section on page 2-10

through the

“SMDS Encapsulation” section on page 2-11

show the prompts and provide examples for configuring each encapsulation type. No further
configuration is needed for HDLC encapsulation.

Sample configuration for the following encapsulation types are provided in this section:

•

PPP Encapsulation

•

Frame Relay Encapsulation

•

LAPB Encapsulation

•

SMDS Encapsulation

PPP Encapsulation

The following is an example of a typical PPP encapsulation configuration:

Would you like to enable multilink PPP [yes]:

Enter a remote hostname for PPP authentication [Router]:

Enter a password for PPP authentication:

Note

The password, which is used by the Challenge Handshake Authentication Protocol (CHAP)
authentication process, is case sensitive and must exactly match the remote router’s password.

Frame Relay Encapsulation

The following is an example of a typical Frame Relay encapsulation configuration:

The following lmi-types are available to be set,

when connected to a frame relay switch

[0] none

[1] ansi

[2] cisco

[3] q933a

Enter lmi-type [2]:

Note

The setup command facility prompts for the data-link connection identifier (DLCI) number only if you
specify

none

for the Local Management Interface (LMI) type. If you accept the default or specify

another LMI type, the DLCI number is provided by the specified protocol.

Enter the DLCI number for this interface [16]:

Do you want to map a remote machine’s IP address to dlci? [yes]:

IP address for the remote interface: 2.0.0.2

Do you want to map a remote machine’s IPX address to dlci? [yes]:

IPX address for the remote interface: 40.1234.5678

Serial interface needs clock rate to be set in dce mode.

Summary of Contents for 2431 - IAD Router





























































































































Search results

Summary of Contents for 2431 - IAD Router

Reviews:

Related manuals for 2431 - IAD Router

Brands by name

Popular brands

Cisco 2431 - IAD Router, Software Configuration Manual

Search results

Summary of Contents for 2431 - IAD Router

Reviews:

Related manuals for 2431 - IAD Router

Brands by name

Popular brands