background image

CL-OPT200T/R  

Rev.900-759-30-00 

 

7.

 

LED Status Indication 

 

     

LED lights up when the camera, cable, fiber optic cable are linked normally.    If it does not light up, please confirm the 

followings: 

z

 

Camera link cable, camera, and fiber optic cable are not connected. 

z

 

No camera link CLK input 

z

 

Data transmission failed via optical transmission 

z

 

No power supplied to CL-OPT200T/R 

 

8.

 

Selection of Power Feeding Method 

 

         

With internal dip switch, power feeding method can be changed.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

(1) CL-OPT200T 

 

 

  

 

 SW1 

・・・

 

ON 

:  Feed the power to the converter unit via 6 pins circular 

connector.      No power is feeded to the camera. 
  (When non-PoCL camera is connected.) 

(Initial Setting) 

 

 

 

OFF  :  Feed the power to both of the converter unit and the 

camera via 6pins ciruclar connector.     
(When PoCL or PoCL-Lite camera is connected.) 

 

(2) CL-OPT200R 

 

 

  

 

 SW1 

・・・

 

ON 

:  Feed the power to the converter unit via 6 pins circular 

connector. 

(Initial Setting) 

 

 

 

OFF  :  Feed the power to the converter unit via the frame 

grabber board. 
  (When PoCL frame grabber board is connected.) 

 

 
 
 
 
 
 
 
 
 
 

©2013 CIS Corporation. All rights reserved. 

11 

 

Summary of Contents for CL-OPT200R
















Reviews: