CipherLab 9500CE Series Reference Manual Download Page 37

Page: 37 / 131

Chapter 2 Installation

2.3 Pistol Grip

When a pistol grip is necessary, install it to the terminal by following the steps:

Place the terminal face down on a flat and clean surface.

Remove the shield-like cover on the back of the terminal by unscrewing.

If there is a hand strap installed, remove it first. Keep the cover and screws for future use
when the pistol grip is not desired.

Connect the power connector from the pistol grip to the receptacle on the terminal.

Screw the pistol grip to the shield-like cover.

Make sure all screws are tightened up but not over-tightened to damage the threads.

Turn on the terminal and test the trigger.

Figure 8: Installing pistol grip

Summary of Contents for 9500CE Series




































































































































Search results

Summary of Contents for 9500CE Series

Reviews:

Related manuals for 9500CE Series

Brands by name

Popular brands

CipherLab 9500CE Series, Reference Manual

Search results

Summary of Contents for 9500CE Series

Reviews:

Related manuals for 9500CE Series

Brands by name

Popular brands