Cino Micro2 Series Quick Start Manual Download Page 6

Verify Micro2 is Working 

After fully charging the battery pack and loading the receipt roll, you can 
print a configuration message to verify Micro2 is in proper working condition. 
A configuration message will be printed after executing the self-test 
procedure. 

 

Steps: 

 
1.  Make sure the Micro2 is power off. 

 
2.  Press and hold the FEED Button and then press POWER Button. 

 
3. Release both POWER and FEED buttons. The LED1-4 will flash 5 times 

to indicate the battery status firstly, then the LED1 gives short orange 
blinks 10 times. The Micro2 will start printing a configuration message. 

 
4.  Pull one edge of the receipt paper against the tear bar to tear the 

configuration message down.

 

 

This message provides information on firmware version, communications, 
power management, printer control setting, general specifications head 
resistance and odometer. 

 

 

Using Your Micro2 

Connecting the Printer Via Bluetooth 

 
Please refer to the VersaJet Micro2 User’s Guide on the Internet at 

 

www.cino.com.tw 

for establishing Bluetooth connection. 

 
 
 
 
 
 
 
 
 

 
 
 

Connecting the Printer Via RS232 

 
 

Host Interface Connector 

 
 
 
 
 
 
 
 
 

 
 

1. Plug the connector of the RS232 cable into the Host Interface Connector 

of the printer. 

 
2.  Power on the printer. The LED1-4 will flash 5 times to indicate the battery 

status. Then the LED1 indicator will flash green at 2 seconds intervals. 

 
3.  The printer is now ready to print. 

 

Summary of Contents for Micro2 Series













Reviews: