manualshive.com logo in svg

Cincoze CV-108R-R10/P1001, User Manual

Share
Download
Cincoze CV-108R-R10/P1001 User Manual Download Page 92

CV-100/P1000 Series

Industrial Panel PC

|  User’s Manual

92

Chapter 4: BIOS Setup

4.4.2 South Bridge

■

Azalia HD Audio

Control detection of the Azalia device.

Audio Controller

Enabled: Azalia will be unconditionally enabled.

Disabled: Azalia will be unconditionally disabled.

■

USB Configuration

XHCI Mode

This setting disables/enables the USB XHCI controller. The eXtensible Host Controller 
Interface (XHCI) is a computer interface specification that defines a register-level 
description of a Host Controller for Universal Serial Bus (USB), which is capable of 
interfacing to USB 1.0, 2.0, and 3.0 compatible devices. The specification is also 
referred to as the USB 3.0 Host Controller specification.

USB 2.0 (EHCI) Support

This setting disables/enables the USB EHCI controller. The Enhanced Host Controller 
Interface (EHCI) specification describes the register-level interface for a Host Controller 
for the Universal Serial Bus (USB) Revision 2.0.

USB RMH Mode

This item will allow users to enable or disable USB RMH Mode.

USB Port 0

This item will allow users to enable or disable USB Port 0.

USB Port 1

This item will allow users to enable or disable USB Port 1.

USB Port 2

This item will allow users to enable or disable USB Port 2.

USB Port 3

This item will allow users to enable or disable USB Port 3.

■

Wake On LAN Enable

This item enables or disables Wake On LAN (WOL) function.

Summary of Contents for CV-108R-R10/P1001
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands