background image

ONT G-25E Hardware Installation Manual

 

About This Document 

 
 

Purpose 

 

This guide describes how to install the CIG optical network termination unit (ONT) at the 

customer premises. 

 

Intended Audience 

 

This document is intended for technicians responsible for: 

z

 

Unpacking and mounting the ONT and power supply 

z

 

Connecting the ONT to the PON network 

z

 

Connecting services to the ONT 

 

Chapter Overview 

 

This manual is organized as follows: 

 

Chapter 1: Product Description 

Provides an introduction to the ONT including physical, electrical, environmental and optical 

specifications. Compliance information is also provided. 

Chapter 2: Safety 

Provides electrical, electrostatic, and laser safety information; fiber optic cable handling 

techniques are also discussed. 

Chapter 3: Installing the ONT 

Describes installation procedures including site preparation, unpacking and mounting the ONT, 
connecting power and fiber optic and cables, connecting service cables, activating the ONT, and 

verifying the installation. 

Chapter 4: Troubleshooting 

Explains ONT LED behavior and provides basic troubleshooting guidelines. 

313-12201-02 Rev. B: August 2007 

Cambridge Industries Group Co. Ltd 

VI

 

Summary of Contents for G-25E





















Reviews: