10
their training . But how do you train to achieve those aims in the most
efficient possible manner? How do you find the right intensity of effort
during the training? CICLO
InZone
®
is the optimum training ZONE for
effort, resistance and weight loss .
What does CICLOInZone
®
do?
It calculates the optimum training zone for effort, resistance and
weight loss . The values vary from person to person and they offer a
valid training support – always staying between 70 % and 85 % of the
maximum heart rate .
(+/- 5% of tolerance, taking into consideration the actual heart rate
when at rest and the level of training) .
The question of burning fat is seen in the “correct” light with
CICLO
InZone
®
– on the basis of the personal data collected .
9. Battery change
CM 8.3A:
First you should put CM 8 .3A into the “Powerdown Mode”
(see chapter 5 Settings) Open battery cap with a coin (unscrew to the
left) . Insert battery type CR2032 (please use battery with smooth minus-
pole) with plus-pole facing up . Close battery cap, being sure not to over
tighten . After inserting the battery the display will show normal mode .
(Speed-)Transmitter:
Open battery cap at the top of the transmitter
with a coin (unscrew to the left), remove old battery and insert new 12
V battery, type 23A (with pluspole facing up) . Close battery cap, being
sure not to over tighten .
(Battery change in the optional cadence transmitter works in the same
way .)
Please do not throw away battery in your normal garbage.
10. Trouble shooting
Faulty or no display
- check to see if battery is installed properly or replace battery (Attention:
removing battery will clear all settings and values in the CM 8 .3A)
- press AC-button on the rear of the computer
Actual Speed not displayed
- transmitter hasn`t been initialized (see chapter 5)
- check to see if wheel-sensor is mounted properly
- check the position of the spoke magnet (max . 3 mm distance to wheel-
sensor)
- make sure CM 8 .3A is mounted in bracket correctly
- check wheel circumference
- start transmitter search (press left button for 3 seconds)
Speed to high or to low
- check wheel circumference
- check to see if you are using miles or kilometers
Transmitters cannot be initialized
(initialization is very slow or “error” displayed)
- Tranmitter battery is discharged or transmitter is defect
- Transmitter has already been initialized for one of the bikes . If you still
want to initialize the transmitter for the current bike you must initialize
the transmitter again for the other bike, but without an active transmit-
ter . “Error” will be displayed . Now you can initialize it again with the
choosen bike .
Automatic search of the transmitter doesn’t start by moving
the bike.
- CM 8 .3A is not correctly located in the handlebar bracked
- A transmitter has already been found (CM 8 .3A displays SPD 0) e .g . if
you switch bikes . If you stay in the transmitting area of the first trans-
mitter CM 8 .3A displays 0 . If CM 8 .3A is outside the transmitting area
it will display “-“ . With the next movement of the bike the transmitter
search will start again .
- transmitter hasn`t been initialized (see chapter 5)
No heart rate displayed or values displayed are incorrect or
unstable
- proof whether heart rate is switched on in setting mode
- Check transmitter belt (battery)
- Skin too dry or cold
- Distance between CM 8 .3A and transmitter belt is too big (max . 5m)
- start manual transmitter search (press left button for 3 seconds)
Manual transmitter search doesn’t start
- no transmitter has been initialized
Cadence is not displayed or value incorrect or unstable
- Check whether switched on in setting mode
- Check sensor and magnet for correct installation
- start transmitter search (press left button for 3 seconds)
CM 8.3A is making noise
- its normal because of the automatic movement sensor
PC Recording doesn’t start
- storage is full, you have to delete recorded tours (with HACtronic
program or the reset function in settings of CM 8 .3A see chapter 5;
Attention: the other values will be deleted also)
Wrong values displayed for the altitude
- Check home-altitude values (adjusting mode), you may have adjusted
wrong values
- Air pressure has changed, e .g . caused by changing weather conditions
(readjust current hight)
11. Guarantee
We offer a guarantee for 2 years from the date of purchase on the CM
8 .3A . The guarantee is limited to material and processing faults . Broken
transmitters, or damages of wasted parts of CM 8 .3A are excluded from
the guarantee .
The guarantee is valid only if the computer, with accessories, has been
handled and maintained carefully and according to operating instructions .
The guarantee will take place through changes of or repairing the defective
parts . The guarantee doens’t cover direct, indirect or subsequent damages
which are related to the product .
This guarantee doesn’t limit any rights of the consumer (considering rela-
tive national law) in respect to the dealer .
To return the CM 8 .3A under conditions/terms of the guarantee, please
refer to your dealer, your local distributor or send the computer with the
proof of purchase (date) and all accessories and with sufficient postage
to:
CICLO SPORT SERVICE
K. W. Hochschorner GmbH
Konrad-Zuse-Bogen 8
D-82152 Krailling
E-Mail: [email protected]
Please read through the operating manual again carefully before sen-
ding in the device and check the battery .
In case of valid guarantee claims, the repaired device or a replacement
device will be returned free of charge .
Repair:
If your CM 8 .3A is sent in for repair (or battery change) or if a gua-
rantee claim is not valid, repairs up to EUR 19 .- will be carried out
automatically .
In case of higher repair costs you will be notified . The repaired device
will be sent back COD .
