Chrysler 300 2017 Owner'S Manual Download Page 34 | Manualshive

Page: 34 / 488

background image

General Information

The following regulatory statement applies to all radio
frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, in-

cluding interference that may cause undesired opera-
tion.

NOTE:

Changes or modifications not expressly approved

by the party responsible for compliance could void the
user’s authority to operate the equipment.

WINDOWS

Power Windows

The window controls on the driver’s door control all the
door windows.

There are single window controls on each passenger door
trim panel, which operate the passenger door windows.
The window controls will operate only when the ignition is
in the ACC or ON/RUN position.

NOTE:

For vehicles equipped with the Uconnect system,

the power window switches will remain active for up to
ten minutes after the ignition is placed in the OFF position.
Opening either front door will cancel this feature. The time
is programmable. Refer to “Uconnect Settings” in “Under-
standing Your Instrument Panel” for further information.

Power Window Switches

32

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
32
33
34
35
36
...
»

Summary of Contents for 300 2017









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 300 2017

Brand: ULTIMATE SPEED Pages: 19

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

Brand: Mercedes-Benz Pages: 30

Brand: STC Pages: 6

Sprinter Side Ladder

Brand: FVC Pages: 8

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Brand: Honda Pages: 268

Brand: Whispbar Pages: 15

Brand: Kargo Master Pages: 17

Brand: Funkwerk Pages: 58

GRAND CHEROKEE L 2021

Brand: Jeep Pages: 388

Brand: Geely Pages: 32

Brand: CDI Pages: 2

Brand: Peiying Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands