13
GB
FUNCTION OF DISPLAYS:
TIME-Display:
Shows actually time of exercising in minutes and seconds.
SPEED-Display:
Shows actually speed in km/h during exercise mode.
Shows programs P01~P06 in stop mode.
DISTANCE-Display:
Shows actually distance in KM.
CALORIES-Display:
Shows actually approx. calories in kcal.
The treadmill can only controlled with the supplied remote control. The remote control requires a button cell type CR2032. Insert the battery into
the remote control, observing the polarity. Guide the wristband through the two openings on the back of the remote control to carry the remote
control on your wrist and to operate it. The range is approx.1.5m. If the remote control does not respond, first change the battery.
MANUAL MODE:
How to start manual mode:
1. Put in the AC cable (57) in wall power 230V~50Hz and put on the power switch (46). Put safety clip (15) at the hangrip right (43R) and it will
show normal manual mode.
2. Stand your feet on both side rails.
3. Put the safety key at you exercise cloth and press „ “-key to start with exercising. After a 3 sec. count down, the motor begin to run slowly and
you can step on the running belt and follow the speed.
4. Adjust the speed with “+” and “-“ -keys into desired speed. If put off the safety clip from handrail at any time, the motor stop immediately and
the display will show „- - -“. After put on the safety key on handrail the normal, manually program will show.
Time Program:
On the normal manual mode, press M-key, to enter time program. The time display will flash and the initial value is 30:00. Press “+”- key or “-“-
key to set value. The range is: 5:00-99:00. Press
„ “
-
key to start the program. If set a value the display counts up till zero and then stops running
motor.
Distance-Program:
On the normal manual mode, press M-key, to enter distance program. The distance display will flash and the initial value is 1,00KM. Press “+”-key
or “-“-key to set value. The range is: 0,5-65:0 KM. Press
„ “
-
key to start the program. If set a value the display counts up till zero and then stops
running motor.
COMPUTER MANUAL
Time → Programs in 20 intervals of time
↓ Program
1
2
3
4
5
6
7
8
9
10
11 12
13 14 15 16 17 18 19 20
P01
Km/h 1
2
3
4
5
4
3
2
1
2
3
4
5
4
3
2
1
2
3
2
P02
Km/h 2
2
3
3
4
4
5
5
6
6
5
5
4
4
3
3
2
2
3
3
P03
Km/h 1
2
3
2
3
4
3
4
5
4
5
6
5
4
5
4
3
4
3
2
P04
Km/h 2
3
3
4
3
4
4
5
4
5
5
6
5
6
6
5
4
3
2
1
P05
Km/h 2
2
3
4
5
6
6
5
4
3
3
2
3
4
4
5
6
5
4
3
P06
Km/h 1
2
3
3
3
4
5
6
6
6
5
4
3
2
2
2
3
4
3
2
Display
Preset Value
Setting Range
Display Range
TIME (MIN:SEK) 0:00
30:00
5:00-99:00
0:00-99:59
KM/H
0.0
N/A
N/A
1.0-8.0
KM
0.00
1.00
0.5-65.0
0.00-99.99
CALORIES (Kcal) 0
50
10-995
0-999
PROGRAM
FUNCTION OF KEYS:
P -key:
On the stop status, press P-key to select exercising speed
programs P01-P06.
„
“-key:
Press this key to start chosen exercise program or stop
the exercise program.
“+”-key:
Press speed up key increase settings or motor speed.
“-”-key:
Press speed down key decrease settings or motor speed.
M-key:
Select key of time-, distance- or calories preset program.
S -Key:
Press S-key during exercise to interrupt the program and
stops the treadmill after a 1 min count down.
Calories-Program:
On the normal manual mode, press M-key, to enter
calories program. The calories display will flash and
the initial value is 50kcal. Press “+”-key or “-“-key to
set value. The range is: 10-995kcal. Press
„ “
-
key to
start the program. If set a value the display counts up
till zero and then stops running motor.
Exercise programs P01-P06:
On the normal manual mode, press P-key to choose
one of the exercise speed programs P01-P06. Each
program is divided into 20 intervals of time and the
speed changes as following program list shows. Initial
setting time is 30min, set a time for training session
and press
„ “
-
key to start the program. Press speed
“+” or “-“-key to adjust speed during the program if it is
to quick or slow. With next intervals of time the speed
level will change back to program mode. If the pro
-
gram runs till end of time the motor will stop running
after the display counts down time to zero. Pressing
„ “
-
key to finish earlier the program.
