Chore-Time 108 FLEX-AUGER Installation And Operator'S Manual Download Page 3

Bin Fill Cap Kit

Introduction

3

MA1038D

Safety

Caution, Warning and Danger Decals

 have been placed on the equipment to warn of potentially dangerous situations. Care 

should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety decals 

immediately.

Safety–Alert Symbol

This is a safety–alert symbol. 

When you see this symbol on your equipment, be alert to the potential for 

personal injury. This equipment is designed to be installed and operated as safely as possible...however, 
hazards do exist.

Understanding Signal Words

Signal words

 are used in conjunction with the safety–alert symbol to identify the severity of the warning.

DANGER

 indicates an imminently hazardous situation which, if not avoided, 

WILL

 result in death or serious 

injury.

WARNING

 indicates a potentially hazardous situation which, if not avoided, 

COULD

 result in death or serious 

injury.

CAUTION

 indicates a hazardous situation which, if not avoided, MAY result in minor or moderate injury.

Follow Safety Instructions

Carefully read all safety messages in this manual and on your equipment safety signs. Follow recommended precautions and 

safe operating practices.

Keep safety signs in good condition. Replace missing or damaged safety signs.

Decal Descriptions

DANGER: Moving Auger

This decal is placed on the End Cap Weldment and Clean-out cover. Severe 

personal injury will result, if the electrical power is not disconnected, prior to 

servicing the equipment.

DANGER: Electrical Hazard

Disconnect electrical power before inspecting or servicing equipment unless 

maintenance instructions specifically state otherwise.

Ground all electrical equipment for safety.

All electrical wiring must be done by a qualified electrician in accordance with local and 

national electric codes.

Ground all non-current carrying metal parts to guard against electrical shock.

Electrical disconnects and over current protection are not supplied with the equipment.

DANGER: Springing Auger

Use caution when working with Auger. Springing Auger may cause personal injury.

Attention: Read the Manual

See the manual for detailed installation instructions.

Introduction

Manboot 3/98

Summary of Contents for 108 FLEX-AUGER





















Reviews: