manualshive.com logo in svg

ChildLife PG134, Assembly Instructions Manual, Page: 14 / 35

Share
Download
ChildLife PG134 Assembly Instructions Manual Download Page 14

14

#04

#12

#13

#11

#42

#40

10"

2"

FLUSH

#04

3. Attach item #11 to the backside of ladder assembly
    approximatley 2" from bottom of  items #01, #04, and #18.

extend 10" past item #04.

4. Attach items #12 and #13 to items #03 and #04 with angled
    surface flat against items #04 and #03. Attach items #11, #12,

 and #13 using hardware items #40 and #44.  

    

PIPE RUNG 

 ASSEMBLY

 

 

      

HARDWARE NEEDED

#40 

5/16” FLAT WASHER 

 

 

(7)

#41 

5/16” X 4” LAG SCREW 

 

 

(2)

#42 

5/16” X 5” LAG SCREW 

 

 

(5)

#64 

#10 X 2” SELF TAPPING SCREW 

(10)

using hardware items #40 and #44. Left end of item #11 should 

#41

#42

#40

PARTS NEEDED

#03   84” LADDER SIDE  LEFT       

 

(1)

#12 

45 DEGREE ANGLE BRACE (RIGHT)  (1)

#13 

45 DEGREE ANGLE BRACE (LEFT) 

(1) 

#19 

21 3/8” LADDER RUNG 

 

 

(5)

1. 

Slide Ladder Rungs #19 into Ladder center #18 
and Ladder Side #03 onto rungs #19 as shown. 

24 5/8”

2.

Angle sides face up

Secure Ladder Rungs #19 with Self Tapping Screws 
#64 as shown.  The ladder should have a width of 
24 5/8” as shown.

FLIP STEP 2 ASSEMBLY OVER AND CONTINUE WITH STEP 3.

Summary of Contents for PG134




































Reviews:

No comments