H03743:11/04
5
S
TEP
6 - D
IAGRAM
6:A
TTACH
S
PRING
TO
S
TABILIZING
B
ARS
READ THIS ENTIRE STEP BEFORE STARTING THE PROCEDURE TO SELECT A SPRING
R
R
R
R
R
HEIGHT POSITION AND TO ATTACH SPRING
R
R
R
R
R
TO THE STABILIZING BARS
S
S
S
S
S
. REVIEW DIAGRAM 1.
1.
1.
1.
1.
1.
Decide on your preference of height placement of Spring
R
R
R
R
R
. You have three position choices, highest, middle and lowest holes
in Spring
R
R
R
R
R
are noted in
Diagrams 1
and
6
. After you select your height, attach one end of the long end of Scissor Arm Assembly
A
A
A
A
A
to Spring
R
R
R
R
R
by first inserting a Hex Head Machine Screw
B
B
B
B
B
through selected position hole in Spring
R
R
R
R
R
then through one end of Scissor
Arm Assembly
A
A
A
A
A
,
add a Lock Nut
C
C
C
C
C
,
(with metal threads of Lock Nuts
C
C
C
C
C
to be inserted first),
exactly as shown. Repeat this procedure
until one end of each of the
(4)
Scissor Arm Assemblies
A
A
A
A
A
is attached to Spring
R
R
R
R
R
at the same height position. Tighten all
(4)
Hex
Head Machine Screws
B
B
B
B
B
with a 5/16 inch wrench while holding Lock Nuts
C
C
C
C
C
with a 7/16 inch wrench. Tighten each assembly securely
.
2.
2.
2.
2.
2.
Carefully lift Spring
R
R
R
R
R
into the crib. Spring
R
R
R
R
R
will attach to the outside holes in the two installed Stabilizing Bars
S
S
S
S
S
. Insert a Hex
Head Machine Screw
B
B
B
B
B
first through the remaining long end of the Scissor Arm Assembly
A
A
A
A
A
through the hole in Stabilizing Bar
S
S
S
S
S
,
add a Lock Nut
C
C
C
C
C
(with metal threads of Lock Nuts
C
C
C
C
C
to be inserted first)
. See
Diagram 6
and follow the procedure exactly. Repeat
the procedure with the remaining
(3)
long ends of the Scissor Arm Assemblies
A
A
A
A
A
to Stabilizing Bars
S
S
S
S
S
. Tighten all
(4)
Hex Head Machine
Screws
B
B
B
B
B
while holding Lock Nuts
C
C
C
C
C
with a 7/16 inch wrench. Tighten each assembly securely.
3.
3.
3.
3.
3.
Whenever you decide on another height position first remove the crib mattress. Remove Spring
R
R
R
R
R
by detaching the spring from
the Stabilizing Bars
S
S
S
S
S
by loosening and removing the
(4)
Lock Nuts
C
C
C
C
C
and removing the
(4)
Hex Head Machine Screws
B
B
B
B
B
(installed
in
2
above)
by using a 7/16 inch wrench and a 5/16 inch wrench. Carefully lift the spring from the crib. Make your selected height position
change by following
1
1
1
1
1
.
of this Step. Then follow
2.
2.
2.
2.
2.
to reinstall Spring
R
R
R
R
R
, again tighten all Hex Head Machine Screws
B
B
B
B
B
securely as
directed.
A
A
R
LOWEST
POSITION
MIDDLE
POSITION
HIGHEST
POSITION
Stabilizer Bars
S
with End
Plates
D
&
E
attached
Short arm of Scissor
Arm Assembly
A
Long arm of Scissor
Arm Assembly
A
C
C
B
NOTE: CRIB IS DELETED FROM DIAGRAM FOR CLARITY & DETAIL
