H03743:11/04
2
P
REPARATION
S
TEP
1 - D
IAGRAM
1: A
SSEMBLE
S
PRING
Carefully remove and lay out all hardware and parts. During the assembly process whenever using screws or bolts (fastening devices),
check each with this hardware list, by letter and size identify by placing each fastening device on the diagram of the item which is
sketched actual size. Be sure to use the proper size specified in the assembly directions. Hardware Bag may contain extra fastening
devices. Check quantities and match to
Hardware Bag and Carton Parts Lists.
If a part is missing or broken contact Child Craft
Customer Service at 1-877-265-9046, FAX: 812-883-1819, http://www.childcraftindustries.com for a replacement part or instructional
literature. Before making this contact identify your crib. Model identification numbers are stamped on a label attached to the inside face
of End
M
bottom rail. Include this information with your request for a part or literature for your crib.
DO NOT SUBSTITUTE PARTS!
Record the complete model identification number now:
#______________________________________
Attach the short section of the
(4)
Scissor Arm Assemblies
A
A
A
A
A
to Spring
R
R
R
R
R
using
(4)
Hex Head Machine Screws
B
B
B
B
B
and
(4)
Lock Nuts
C
C
C
C
C
placed exactly as shown in
Diagram 1
.
NOTE:
The metal threads of Lock Nuts
C
to be inserted first over Washer Head Machine
Screws
B
B
B
B
B
as shown in Enlarged Section View .
Be sure to use the proper receiving holes in Spring
R
R
R
R
R
as shown . This procedure will
be accomplished from the underside of Spring
R
R
R
R
R
. Tighten all
(4)
Hex Head Machine Screws
B
B
B
B
B
with a 5/16 inch wrench while holding
Lock Nuts
C
C
C
C
C
with a 7/16 inch wrench. Tighten each assembly securely.
UNDERSIDE OF SPRING
R
R
R
R
R
Long arm of Scissor Arm Assembly
A
Short arm of Scissor Arm Assembly
A
Long arm of
Scissor Arm
Assembly
a
Short arm of
Scissor Arm
Assembly
A
Plastic pouch
Lowest position
Middle position
Highest position
Enlarged View
Plastic insert in
Lock Nut
C
B
C
A
R
A
B
R
A
C
SEE
ENLARGED
VIEW
Mount an End Plate - Right
E
E
E
E
E
and an End Plate - Left
D
D
D
D
D
to ends of each Stabilizing Bar
S
S
S
S
S
using
(4)
Hex Head Machine Screws
B
B
B
B
B
and
(4)
Lock Nuts
C
C
C
C
C
in each Stabilizing Bar
S
S
S
S
S
exactly as shown.
IMPORTANT: End Plates
D
D
D
D
D
&
E
E
E
E
E
must be positioned in the correct mounting
holes to Stabilizing Bars
S
S
S
S
S
exactly as shown.
Tighten down Hex Head Machine Screws
B
B
B
B
B
and Lock Nuts
C
C
C
C
C
securely using a 5/16
and a 7/16 inch wrench.
See Enlarged View
B
D
S
Enlarged View
Plastic insert in
Lock Nut
C
B
E
slot
slot
S
B
D
or
E
End Plate
INSTALL END PLATES
D
D
D
D
D
&
E
E
E
E
E
EXACTLY AS SHOWN
C
C
S
TEP
2 - D
IAGRAM
2:A
SSEMBLE
S
TABILIZING
B
ARS
