Child Craft CRIB’N’DOUBLE Page 4 Manual Download

Page: 4 / 7

CCH02703:12/99

TEP

4 - D

IAGRAM

4:A

TTACH

TABILIZING

TEP

5 - D

IAGRAM

5: S

PRING

NSTALLATION

Locate “Tabs” on Spring

and rotate Tabs upward. Position the

four Tabs on Spring

to the desired height allowed by the threaded

holes located on the 4-Position Spring Bracket

. Install a Hexhead

Machine Screw

through each Spring Tab and into the selected threaded

receiving hole on Spring Bracket

. Tighten Screws

with Hexhead

Wrench

or a 10mm (3/8”) wrench. Follow the same procedure when

changing spring heights at a later date. Periodically check Hexhead Ma-
chine Screws

and tighten if needed.

TEP

6 - D

IAGRAM

6: I

NSTALL

ROPSIDE

Align Plastic Guides
(Factory installed) on
Dropside

L L

with

dropside hardware
mounted on post from
underneath. An as-
sistant is very help-
ful. After all four plas-
tic guides are aligned
with the hardware,
lift Dropside “UP” and
allow it to latch into
the raised position.

After Dropside

is installed on the
tracks and is latched
in the “UP” position,
insert a Machine
Screw

into a

Rubber Washer

and thread into hole
in bottom of Lower
Track Assemblies

TO LOWER DROPSIDE

FIRST - LIFT THE DROPSIDE,
SECOND - WITH KNEE PUSH
IN ON CENTER OF BOTTOM
RAIL OF DROPSIDE TO RE-
LEASE LATCH ON LOWER
PLASTIC LATCH. LOWER
DROPSIDE BY HAND. TO
RAISE DROPSIDE

: PULL

“UP” UNTIL LOWER PLASTIC
GUIDES LATCH IN SLOT IN
LOWER TRACKS

ALWAYS BE SURE CRIB SIDE IS “UP” AND “LATCHED” BEFORE LEAVING CHILD IN CRIB.

Mount the Stabilizing Bar Assembly

to Footboard

and Head-

board

. Insert (2) Pan Head Machine Screws

through the holes

in Sta-Bar Bracket - Right

, and through the holes in Stabilizing Bar

N N

. Attach (2) Insert Locknuts

to Machine Screws

tighten securely. See Enlarged View for the proper installation of
Locknut

. Follow the same procedure for attaching Stabilizing Bar

N N

to Headboard

J J

I I

o r

Plastic insert in

Locknut

NOTE: Mount all 4 “Tabs” on Crib Spring

at the same vertical mattress position.

Corner Post of

Highest mattress position

Lowest mattress position

Mattress side
of Spring

M M

“Tab”

I I

Align Upper
Plastic Guide
with Upper
Track

Align Lower
Plastic Guide
with Lower
Track

Align all four plastic guides with installed

tracks from underneath - then lift “UP”

until Lower Plastic Guides latch.

LOCKING MECHANISM

NOTE: It may be necessary to Flex the Locking Mechanism

toward outside of crib to engage the Lower Tracks

I I

Summary of Contents for CRIB’N’DOUBLE








Search results

Summary of Contents for CRIB’N’DOUBLE

Reviews:

Related manuals for CRIB’N’DOUBLE

Brands by name

Popular brands

Child Craft CRIB’N’DOUBLE, Manual

Search results

Summary of Contents for CRIB’N’DOUBLE

Reviews:

Related manuals for CRIB’N’DOUBLE

Brands by name

Popular brands