CCH01760:07/00
9
S
TEP
13 - R
EMOVE
S
TATIONARY
S
IDE
& F
OLDING
S
IDE
IMPORTANT! Read STEP 13 completely before continuing any further.
FIRST: Locate three Panhead Machine Screws
HH
HH
HH
HH
HH
and Head Frame
O
O
O
O
O
. Remove the three Panhead Machine Screws
A
A
A
A
A
from the Head Bottom Panel
N
N
N
N
N
very carefully, see Diagram 12
. Try to prevent the Bed Rails
G
G
G
G
G
and
H
H
H
H
H
from disengaging from the Head Bottom Panel
N
N
N
N
N
.
SECOND: Mount Head Frame
O
O
O
O
O
to the outside face of Head Bottom Panel
N
N
N
N
N
.
(The Head Frame
O
O
O
O
O
will have the Strike Plate mounted away from the mattress
area.) Insert three Panhead Machine Screws
HH
HH
HH
HH
HH
through the Head Frame
O
O
O
O
O
, then through the Head Bottom Panel
N
N
N
N
N
and into the Bed Rails
G
and
H
H
H
H
H
. Insert a Plug
AA
AA
AA
AA
AA
into each of the two holes located on the inside of the Wide Bed Rail
G
G
G
G
G
.
(Note: After removing Machine Screws
A
A
A
A
A
the Plugs
AA
AA
AA
AA
AA
may have stayed in the holes.) Pull out each Machine Screw
HH
just enough to allow the Plug
AA
to be fully inserted in the hole. Tighten each
Machine Screw
HH
until secure, but do not overtighten. Reattach the Narrow Bed Rail
H
H
H
H
H
in the same manner.
THIRD: Place a Plastic Plug Button
E
E
E
E
E
into each of the four holes shown in Diagram 13
. Also place a Plastic Plug Button
E
E
E
E
E
into the outside face of Chest
F
F
F
F
F
at the location of where the Stationary Side
P
P
P
P
P
and the Folding Side
Q
Q
Q
Q
Q
were attached as a "Crib".
D
IAGRAM
12
G
Install
E
N
H
Large Storage Drawer
Mattress Support
Guide Block
Remove these
three screws
A
very carefully
Mattress Support
G
H
Both faces
N
Install
E
Insert the (3)
Panhead Machine
Screws
H H
H H
H H
H H
H H
thru
receiving holes in
Head Frame
O
O
O
O
O
,
then thru Bottom
Panel
N
N
N
N
N
and into
Bed Rails
G
G
G
G
G
&
H
H
H
H
H
.
Secure with Plugs
A A
A A
A A
A A
A A
. See Step
13.
O
Strike plate
D
IAGRAM
13
Remove Spring Hangers
JJ
JJ
JJ
JJ
JJ
from Spring
R
R
R
R
R
. Also remove Dust
Bottom
U
U
U
U
U
. Place Crib Spring
R
R
R
R
R
into assembled unit using guide
blocks to locate Crib Spring
R
R
R
R
R
. See Diagram 1 and MAIN DIAGRAM
2. Note: Crib Spring
R
R
R
R
R
will now rest on wooden mattress supports.
S
TEP
13A - R
EMOVE
S
PRING
H
ANGERS
& D
UST
B
OTTOM
S
TEP
14 - P
LACEMENT
OF
E
XTENSION
S
PRING
E
XTENSION
M
ATTRESS
& C
RIB
M
ATTRESS
Place the optional Extension Spring and the optional Extension
Mattress into place where Chest
F
F
F
F
F
was removed.
If your model
Crib'n'Bed did not include an Extension Spring or Extension Mat-
tress you may order them from your dealer or Child Craft at (812)
883-3111 by using your MasterCard or Visa charge to have these
items sent to you. Again, after assembly is complete place this set
of assembly instructions back into the Plastic Pouch factory mounted
to Crib Spring
R
R
R
R
R
for permanent storage. Place crib mattress on crib
spring and Your "Bed" is now ready for use.
D
IAGRAM
14
NOTE: Notches
are to be placed to
inside of "Bed".
H
M
Lower drawer
Shown as "Bed"
II
To Operate Latch Pins on Folding Side
Q
Q
Q
Q
Q
, when set up as a “Crib”, follow directions listed below. Refer to Main Diagram 2, Diagram
3 and the NOTICE listed on Page 8. Place a hand on each latch pin, while pulling out, slide each handle toward the middle of crib, the latch pins
will now be free to allow the folding side to be placed in the Down Position. Repeat the same operation to place Folding Side
Q
in Upward Position,
only after pulling latch pins out and to middle of crib, align with receiving hole in strike plate located on inside of Chest
F
and on Head Top Panel
O
,
release latch pins into receiving holes. Check to be sure the Latch Pins are in proper position before leaving your baby in crib. Always check to be
sure the side, when in the Upward Position, is secure. IMPORTANT: See Notice regarding latch pins on page 8.
IMPORTANT! BE SURE ALL SCREWS ARE TIGHTENED AT THIS TIME, SECURE, BUT DO NOT OVERTIGHTEN. A PERIODIC CHECK SHOULD BE MADE
OF ALL SCREWS IN THIS UNIT TO BE SURE THEY REMAIN TIGHT.
IMPORTANT! Refer to Warnings & Cautions listed on pages 7 and 8, Maintenance, Cleaning Instructions, Storage and Use of your Child
Craft Crib'n'Bed listed on page 8. Store all parts not used, for possible future use in case you will want to convert “Bed” back into a “Crib”.
Place assembly directions in storage pouch mounted on Crib Spring
R
R
R
R
R
.....
In the event you choose to convert "Bed" back into a "Crib" at a later date, first remove Head Frame
O
O
O
O
O
by reversing procedure in Step
13. Second, Cushioned Cap Rail
II
II
II
II
II
must be removed from the top edge of Foot Panel
M
M
M
M
M
. Start by pulling up on one end of Cushioned
Cap Rail
II
II
II
II
II
, (if you have difficulty, carefully use a slotted screwdriver tip to pry between the top edge of the Panel
M
M
M
M
M
and Cushioned
Cap Rail
II
II
II
II
II
). Be very careful to not damage either part. Then proceed with Steps (4) thru ( 9) for “Crib” buildup.
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: 812-883-1819
http://www.childcraftind.com
child craft
child craft
child craft
child craft
child craft
made in usa
