Remove the two top drawers from Chest
F
F
F
F
F
(if your chest has 3 drawers).
Refer to the following directions for drawer removal and also refer
to Diagram 4.
Note: Remove only the top drawer if your chest has
a dressing area. Place the one Flathead Machine Screw
B
B
B
B
B
through hole
provided on inside of Chest
F
and into hole provided in the end of rail of Folding
Side
Q
Q
Q
Q
Q
. Insert a Plug
AA
AA
AA
AA
AA
into the hole located on the bottom edge of the rail
of Folding Side
Q
Q
Q
Q
Q
. Pull out Flathead Machine Screw
B
just enough to allow
the Plug
AA
AA
AA
AA
AA
to be fully inserted in hole. Tighten Flathead Machine Screw
B
B
B
B
B
until secure, but do not overtighten. See Diagram 1 and MAIN DIAGRAM 2.
(Be sure that you have placed the hinged portion of Folding Side
Q
Q
Q
Q
Q
to outside
of crib as shown on Diagram 3 ) Important! Refer to Notice on Page
(8).
6
CCH01760:07/00
S
TEP
7 - A
TTACH
F
OLDING
S
IDE
(
CONTINUED
)
Insert (3) Panhead Machine Screws
FF
FF
FF
FF
FF
and (3) Threaded Inserts
EE
EE
EE
EE
EE
into the (3) empty holes in Head Frame
O
O
O
O
O
. Note: Threaded Inserts
EE
EE
EE
EE
EE
will
be placed into holes from the inside of the Crib'n'Bed and the Machine Screws
FF
FF
FF
FF
FF
will go into holes from the outside of Crib'n'Bed. Thread both parts
together and tighten securely using a flathead screwdriver and the enclosed Allen Wrench
GG
GG
GG
GG
GG
. Refer to Diagram 1 and MAIN DIAGRAM 2.
D
IAGRAM
4
PRESS DOWN HERE
Then pull drawer out
Drawer Back
Drawer End
S
TEP
8 - I
NSTALL
D
UST
B
OTTOM
Install Dust Bottom
U
U
U
U
U
onto mattress supports on the inside face of the Wide
Bed Rail
G
G
G
G
G
and Narrow Bed Rail
H
H
H
H
H
. Position the routs in the Dust Bottom
U
U
U
U
U
to mount over the guide blocks located on the matttress supports. See
Diagram 5.
D
IAGRAM
5
U
Routs
Guide Blocks will be
inserted through
these routs.
P
G
Mattress support
Guide blocks
F
O
N
M
DIRECTIONS FOR REMOVAL OF SMALL
DRAWERS IN CHEST
F
F
F
F
F
WITH LOCK-IN
DRAWERS, ALSO SEE DIAGRAM 4.
Pull drawer open until it is stopped by the stop
lock on the plastic drawer glide. PRESS DOWN on
the release tab and pull the drawer out. Note: It will
be necessary to PRESS DOWN on the release tab
located on each side of the drawer ends simulta-
neously for the lock-in mechanism to be released.
To reinsert the drawer into Chest
F
F
F
F
F
, simply align
each side of drawer with the drawer glide and slide
into place..
S
TEP
9 - I
NSTALL
C
RIB
H
ANGERS
& C
RIB
S
PRING
Locate Crib Spring
R
R
R
R
R
and the (4) Spring Hangers
JJ
JJ
JJ
JJ
JJ
. Note: Be sure
smooth side of Crib Spring
R
R
R
R
R
wire is placed upward as illustrated in
Diagram 6. Insert Spring Hanger
JJ
JJ
JJ
JJ
JJ
into brackets attached to frame of
Crib Spring
R
R
R
R
R
as shown.
(A light blow with a hammer may be required to
fully engage Spring Hangers
JJ
JJ
JJ
JJ
JJ
). Carefully install Crib Spring
R
R
R
R
R
by placing
each of the (4) Spring Hangers
JJ
JJ
JJ
JJ
JJ
into a selected position in each of the
four 4-Position Spring Hanger Brackets
LL
LL
LL
LL
LL
mounted on Stationary Side
P
P
P
P
P
and Folding Side
Q
Q
Q
Q
Q
. Note: The lip of the Moulded Plastic Backer will allow
the Spring Hanger
JJ
JJ
JJ
JJ
JJ
to be placed with no difficulty. However, when you
decide on another placement position of Crib Spring
R
R
R
R
R
you will need to place
your thumbnail or a small screwdriver, on the lip of the Moulded Plastic Backer
and hold DOWN in order to raise Spring Hanger
JJ
JJ
JJ
JJ
JJ
from this position, see
Diagram 1A. NOTE:
Refer to Step 3A for directions to project an inverted
tab on an installed 4-Position Spring Hanger Bracket
LL
LL
LL
LL
LL
if needed. Follow
this same procedure whenever you change the Crib Spring
R
R
R
R
R
to another
of the (4) positions.Note: When using the lowest of the 4-Positions; remove
the Dust Bottom
U
U
U
U
U
from the unit and store for possible future use.
D
IAGRAM
6
J J
R
L
L
P
o r
Q
Insert all 4 Spring
Hangers
J J
at
the same height
position.
Note: Mattress & Crib Spring
R
R
R
R
R
must be removed to gain
access to the Plastic Pouch which is mounted to the underside
of Crib Spring
R
R
R
R
R
.
S
TEP
9A - S
TORE
A
SSEMBLY
D
IRECTIONS
FOR
F
UTURE
U
SE
After completing the assembly process, and after making yourself aware of
the Warnings, Cautions, Cleaning, Storage, Use and Maintenance of crib'n'bed,
store the assembly directions in the plastic pouch which was pre-attached
to the underneath side of Crib Spring
R
R
R
R
R
.
Entrance will be gained by removing
mattress and Crib Spring
R
R
R
R
R
. For future referral to the assembly directions you
must remove the mattress and Crib Spring
R
R
R
R
R
to access the plastic pouch to
remove the stored assembly directions.
DO NOT PLACE EXCESS HARDWARE OR
TOOLS IN PLASTIC STORAGE POUCH AS IT
COULD PRESENT DANGER TO A SMALL
CHILD IF RETRIEVED.
IMPORTANT! BE SURE ALL SCREWS AND BOLTS ARE TIGHTENED AT
THIS TIME, SECURE, BUT DO NOT OVERTIGHTEN. A PERIODIC CHECK
SHOULD BE MADE OF ALL SCREWS AND BOLTS IN THIS UNIT TO BE SURE
THEY REMAIN TIGHTENED!
IMPORTANT! CHECK ALL CARTONS AND PACKING MATERIAL BEFORE
DISCARDING TO BE SURE YOU HAVE REMOVED ALL CRIB'N'BED PARTS
AND HARDWARE.
