background image

QMP1MM2

Installation Instructions

6

11. Reinstall end lock(s) into mounting rail using the 5/32" hex

key (J). (See Figure 8)

Figure 8

CABLE MANAGEMENT

1.

Attach all cables to display.

2.

Route cables through cable clips on array assembly (A).
(See Figure 9)

3.

Route cables down cart/stand column and away from mount
following instructions included with the cart/stand column.

Figure 9

ADJUSTMENTS

Display Adjustment

Horizontal position

1.

Using your fingers, slightly loosen horizontal adjustment
knob.  (See Figure 10)

2.

Slide display along array to desired position.

3.

Using your fingers, tighten horizontal adjustment knob. (See
Figure 10)

Pitch / Yaw / Roll Tension

1.

Using your fingers, slightly loosen tension knob. (See
Figure 10)

2.

Adjust display as desired.

3.

Using your fingers, tighten tension knob.

Figure 10

Cart/Stand Adjustment

Follow adjustment instructions included in the cart/stand
installation instructions.

End lock

Centris head

(A)

Square nut

(Display not shown)

Cable Clips

(A)

(Cart/stand column not shown)

Horizontal adjustment knob

Tension knob

(Display not shown)

Summary of Contents for QMP1MM2









Reviews: