background image

PACCS1

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.

 IMPORTANT SAFETY INSTRUCTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components located on the PACCS1 does not exceed
15 lbs (6.8 kg). Use with products heavier than the maximum
weight indicated may result in collapse of the mount and its
accessories causing possible injury.

WARNING:

RISK OF INJURY TO PERSONS! Do not use

this mounting system to support video equipment such as
televisions or computer monitors.

WARNING:

Do not use this product outdoors.

--SAVE THESE INSTRUCTIONS--

DIMENSIONS

14.00

14.00

7.87

7.87

15.50

25.51 EXTENDED

24.64 COLLAPSED

(1.00)

17.51 EXTENDED

15.64 COLLAPSED

MOUNTING HOLES FOR

OPTIONAL 200X200

VESA PATTERN

APPROXIMATE

CENTER OF SCREEN

1.06

ADDED TO

OVERALL

MOUNT DEPTH

1.62

12.88 EXTENDED

11.35 COLLAPSED

18.31

Summary of Contents for PACCS1









Reviews: