CHIEF MSP-DCCPPNR Installation Instructions Manual Download Page 10

Page: 10 / 14

Installation Instructions

MSP-DCCPPNR

TENSION ADJUSTMENTS

Vertical Tilt Tension Adjustment

Using 5/32” Allen wrench, slightly tighten or loosen two
screws, one on each side, equally (see Figure 9).

With display mounted, check for desired vertical tilt ten-
sion.

Repeat Step 1 and Step 2 until desired vertical tilt tension
is obtained.

Lateral Tilt Tension Adjustment

CAUTION: Overtightening lateral adjustment will cause

excessive wear and may distort adjustment
components.

Using a 9/16” wrench, slightly tighten or loosen lateral tilt
tension adjustment nut (see Figure 10).

Mount the display and check for desired tilt tension.

Repeat Steps 1 and 2 until desired tilt tension is obtained.

Rotational Tilt Tension Adjustment

If necessary, loosen or tighten bottom rotational tilt
tension adjustment nut (see Figure 11).

Mount the display and check for desired rotational tilt ten-
sion.

Repeat Steps 1 and 2 until desired rotational tilt tension is
obtained.

Adjustment

Nut

Vertical Tilt
Adj. Screw

Figure 9. Vertical Tilt

Lateral Tilt

Adjustment Nut

Figure 10. Lateral Tilt

Rotational
Adj. Nut

Figure 11. Rotational Adjustment

Summary of Contents for MSP-DCCPPNR















Search results

Summary of Contents for MSP-DCCPPNR

Reviews:

Related manuals for MSP-DCCPPNR

Brands by name

Popular brands

CHIEF MSP-DCCPPNR, Installation Instructions Manual

Search results

Summary of Contents for MSP-DCCPPNR

Reviews:

Related manuals for MSP-DCCPPNR

Brands by name

Popular brands