background image

LCM Video Wall Series

Installation Instructions

10

Adding Displays to Mounting Rails

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components located within the mounting system of the
LCM Series model does not exceed maximum weights listed
in table below.

WARNING:

Improper display installation can result in

serious personal injury or damage to equipment! Install
displays from the bottom to the top. Install all displays evenly
in each row before proceeding to a higher row. Do NOT
mount all of the displays on one side. On the LCM3X3, mount
the center display in each row prior to installing the outside
displays in that same row. (See Figure 13)

Figure 13

CAUTION:

BEFORE adding displays to the mounting rails,

ensure end caps are in place at BOTH ends of mounting rail!

1.

If necessary, make height adjustments to the bottom rail by
using adjustment points on the array heads (X).  (See
Figure 14)

2.

While holding mounting rail, loosen button head screws on
sides of array heads (X).

3.

Level and move mounting rail up or down as necessary.

4.

Tighten button head screws on sides of array heads (X).

Figure 14

5.

Open latch on attached interface brackets. (See Figure 15)

Figure 15

6.

Hang displays with attached interface brackets over
mounting rail.

7.

Raise latch on interface bracket and close into place against
mounting rail. (See Figure 15)

8.

Fasten latch into place using one 1/4-20 x 1-1/4" socket
head screw (

I

). (See Figure 15)

NOTE:

Socket head screws (

I

) must engage through both

holes to be fully secured. (See Figure 15)

9.

Repeat for each interface bracket on the mounting rail.

MODEL

Max Weight
Allowed for EACH
Display

Max Weight
Capacity of
Mounting System

LCM2X2U

125 lbs

(56.7 kg)

500 lbs

(226.8 kg)

LCM3X2U

125 lbs

(56.7 kg)

750 lbs

(340.2 kg)

LCM3X3U

85 lbs

(38.6 kg)

765 lbs

(347.0 kg)

2

1

3

5

4

6

8

7

9

4

2

3

5

Latch

8

(I)

x 2

7

NOTE:

 Secure

screw (

I

)

through both
holes.

OPEN

Latch
CLOSED

Summary of Contents for LCM2X2





















Reviews: