background image

Installation Instructions

 JSBV

2

DISCLAIMER

Milestone AV Technologies, Inc., and its affiliated corporations 
and subsidiaries, intend to make this manual accurate and 
complete. However, Milestone makes no claim that the 
information contained herein covers all details, conditions or 
variations, nor does it provide for every possible contingency in 
connection with the installation or use of this product. The 
information contained in this document is subject to change 
without notice or obligation of any kind. Milestone makes no 
representation of warranty, expressed or implied, regarding the 
information contained herein. Milestone assumes no 
responsibility for accuracy, completeness or sufficiency of the 
information contained in this document.

Chief® and Centris™ are registered trademarks of Milestone 
AV Technologies. All rights reserved.

 IMPORTANT WARNINGS AND 

CAUTIONS!

WARNING:  

A WARNING alerts you to the possibility of 

serious injury or death if you do not follow the instructions.

CAUTION:  

A CAUTION alerts you to the possibility of 

damage or destruction of equipment if you do not follow the 
corresponding instructions.

WARNING:  

Failure to read, thoroughly understand, and 

follow all instructions can result in serious personal injury, 
damage to equipment, or voiding of factory warranty!  It is the 
installer’s responsibility to make sure all components are 
properly assembled and installed using the instructions 
provided.

WARNING:  

Failure to provide adequate structural strength 

for this component can result in serious personal injury or 
damage to equipment!  It is the installer’s responsibility to 
make sure the structure to which this component is attached 
can support five times the combined weight of all equipment.  
Reinforce the structure as required before installing the 
component.

WARNING:  

Exceeding the weight capacity of the mount 

can result in serious personal injury or damage to equipment!  
It is the installer’s responsibility to make sure the combined 
weight of the mount and all attached components does not 
exceed 75 lbs (34.02 kg).

DIMENSIONS

3.94

100

15.75

400

3.94

100

7.87

200

11.81

300

7.87

200

7.87

200

ALL MEASUREMENTS ARE IN 

THE FOLLOWING FORMAT:

[MILLIMETERS]

INCHES

Summary of Contents for J Series









Reviews: