manualshive.com logo in svg

Chicco Fit 4, User Manual

Share
Download
Chicco Fit 4 User Manual Download Page 72

ADDITIONAL INFORMATION

140

141

ADDITIONAL INFORMATION

CLEANING AND MAINTENANCE

 

DO NOT USE BLEACH, solvents or household cleaners as they may 

weaken plastics and straps.

 

DO NOT USE SOAPS OR LUBRICANTS on Harness Adjuster Strap, 

Buckle and LATCH hardware.  It may cause them to malfunction.

• 

Cleaning Softgoods:

 

      

Hand wash using mild soap and water, or machine wash in cold water on 

delicate cycle using mild detergent.  Hang to dry. 

• 

Cleaning Shoulder Pads:

 

   

  Hand wash using mild soap and water.  Hang to dry. 

• 

Cleaning Plastics:

 

      

Sponge clean using warm water and mild soap.  Towel dry.

  

 

 

NEVER

 use Child Restraint without the seat pad.

For softgood removal instructions visit the Chicco website at 

www.chiccousa.com or call 1-877-424-4226.

CLEANING AND MAINTENANCE

Do 

NOT 

remove LATCH or Adjuster straps.  For additional information visit the Chicco

website at www.chiccousa.com or call 1-877-424-4226.

• 

Cleaning Cup Holder: 

    

  Cup Holder is dishwasher safe on top rack only. 

• 

Cleaning Harness: 

 

   

  Sponge clean using warm water and mild soap.  Air dry.  Do NOT machine wash.  
• 

Cleaning LATCH and Adjuster Strap: 

    

  LATCH Straps cannot be replaced.  Sponge clean 

    using warm water only.  Air dry. 
• 

Cleaning Buckle and LATCH Hardware:

 

   

Sponge clean, using warm water only.  If debris in 

  buckle, remove and rinse in warm cup of water.  

  Air dry.  See page 138 for removal instructions.

 

DO NOT USE 

Child Restraint if any part of the harness is damaged. For 

proper removal and installation of the harness straps visit the Chicco website 

at www.chiccousa.com or call 1-877-424-4226.

Summary of Contents for Fit 4










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands