1/2" (12 mm)
3/8" (10mm)
3/8" (10mm)
3/8" (10mm)
CA048361 (1/2")
CA048362 (1/2")
CA048360 (1/2")
3/8" (10mm)
3/8" (10mm)
130
90
0
3
Compression Riveter
CP0214
Limited Warranty: The "Products" of the Chicago Pneumatic Tool Company ("CP") are warranted to be free from defects in material and workmanship for one
year from the date of purchase. This Warranty applies only to Products purchased new from CP or its authorized dealers. Of course, this Warranty does not
apply to products which have been abused, misused, modified, or repaired by someone other than CP or its Authorized Service Representatives. If a CP
Product proves defective in material or workmanship within one year after purchase, return it to any CP Factory Service Center or Authorized Service Center for
CP tools, transportation prepaid, enclosing your name and address, adequate proof of date of purchase, and a short description of the defect. CP will, at its
option, repair or replace defective Products free of charge. Repairs or replacements are warranted as described above for the remainder of the original
warranty period. CP's sole liability and your exclusive remedy under this Warranty is limited to repair or replacement of the defective Product. (Tandem
Cylinder 10,000 Cycles)
(There
Are
No
Other
Warranties
Expressed
Or
Implied
And
CP
Shall
Not
Be
Liable
For
Incidental,
Consequential,
Or
Special
Damages,
Or
Any
Other
Damages,
Costs
Or
Expenses
Excepting
Only
The
Cost
Or
Expense
Of
Repair
Or
Replacement
As
Described
Above.)
Air Supply
For rated tool performance, 90 PSI of clean, dry air is required at
the tool. Whip hose 5/16" I.D. may be used at the air inlet, but
longer runs should be 3/8" I.D. with couplings of a minimum 9/32"
I.D. The use of a CA048360 Chicago Pneumatic Air Line
Separator and Filter and a CA048362 Chicago Pneumatic Air
Line Pressure Regulator mounted as closely as possible to the
tool is recommended.
Lubrication
Daily before using, before putting a new or an old riveter into
service, and after each shift, disconnect tool, blow out air line to
clean it of accumulated dirt and moisture. Pour about 1/2 fl. oz. of
recommended oil into air inlet. Connect tool and operate to allow
oil to be carried to cylinder. In addition, the use of a CA048361
Chicago Pneumatic Air Line Lubricator installed at the end of
each air pipe leading to this pneumatic tool is recommended to
assure a constant and adequate supply of lubricant to valves and
cylinder.
Noise & Vibration Declaration*
2
Vibration value <2.5 m/s , re. ISO 8662-1.
Operation
Throttle lever (112) must first be moved forward axially before
depressing to start cycle. This is a safety feature to reduce
accidental actuations. Once throttle lever is depressed,
compressed air forces the piston and wedge (41) forward, then
one rivet set is driven toward the other exerting compressive
force on the rivet. Force is exerted until the throttle lever is
released, returning the tool to the ready position ending its cycle
of operation.
Sound pressure level 90 dB(A) in accordance with Pneurop
PN8NTC1.2. For sound power, add 10 dB(A).
We, Chicago Pneumatic Tool Company, 1800 Overview Drive, Rock Hill, SC 29730
USA, declare under our sole responsibility that the product to which this declaration
relates, is in conformity with the requirements of the Council Directive of June 1998
on the approximation of the laws of the Member States relating to machinery
(98/37/EC).
Machine Name
CP0214 Compression Riveter
Machine Type
Power Tool with 3/16" or 1/4" shank for use with rivet
sets and various 3/16" or 1/4" shank accessories - No other use is
permitted.
Serial No.
Tools with No. 99090A or higher
Technical Data
Air pressure 90 psi (6.2 bar)
Harmonized Standards Applied
EN292
National Standards Applied
ISO 8662-1, Pneurop PN8NTC1.2
Name and Position of Issuer
W. A. LeNeveu, President, Chicago
Pneumatic Tool Company
Signature of Issuer
Place and Date of Issue
Rock Hill, SC 29730 USA, May 1999
Maintenance
1. Keep tool properly lubricated.
2. Provide 90 PSI of clean, dry air at the tool.
3. Use hose and connections of proper size and in good condition.
4. Set up and maintain a repair and replacement program
scheduled at regular intervals.
5. High wear parts are underlined in parts list.
*These declared values were obtained by laboratory type testing in compliance with the stated standards and
are not adequate for use in risk assessments. Values measured in individual work places may be higher than
the declared values. The actual exposure values and risk of harm experienced by an individual user are
unique and depend upon the way the user works, the workpiece and the workstation design, as well as upon
the exposure time and the physical condition of the user. We, Chicago Pneumatic, cannot be held liable for the
consequences of using the declared values, instead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have no control.
Air Supply Diagram