Chicago Electric 68857 Owner'S Manual & Safety Instructions Download

Page: 7 / 24

Page 7

For technical questions, please call 1-800-444-3353.

Item 68857

6. Grip tool as lightly as possible (while still keeping

safe control of it). Let the tool do the work.

7. To reduce vibration, maintain the tool as

explained in this manual. If any abnormal

vibration occurs, stop use immediately.

Save theSe inStRuctionS.

Grounding

to pRevent electRic ShocK and death FRom incoRRect GRoundinG

WiRe connection: check with a qualified electrician if you are in doubt as to whether the outlet

is properly grounded. do not modify the power cord plug provided with the charger. do not use

the charger if the power cord or plug is damaged. if damaged, have it repaired by a service facility

before use. if the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

double insulated tools: tools with two prong plugs

outlets for 2-prong plug

1. Tools marked “Double Insulated” do not

require grounding. They have a special

double insulation system which satisfies

OSHA requirements and complies with

the applicable standards of Underwriters

Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code.

2. Double insulated tools may be used in either of the

120 volt outlets shown in the preceding illustration.

(See outlets for 2-prong plug.)

extension cords

note:

Extension cords must not be used with this item’s Charger.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

Volts Alternating Current

Amperes

n0 xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking concerning

Risk of Hearing Loss.

Wear hearing protection.
WARNING marking

concerning Risk of Fire.

Do not cover Charger ventilation ducts.

Charge on fireproof surface only.

WARNING marking concerning

Risk of Electric Shock.

Properly connect Charger’s power

cord to appropriate outlet.

WARNING marking concerning

Risk of Explosion.

Do not puncture, short, or open

battery packs and do not charge

damaged battery packs.

Fet

ation

aintenance

Setup

Summary of Contents for 68857

























Search results

Summary of Contents for 68857

Reviews:

Related manuals for 68857

Brands by name

Popular brands

Chicago Electric 68857, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 68857

Reviews:

Related manuals for 68857

Brands by name

Popular brands