background image

SKU 65588 

For technical questions, please call 1-800-444-3353. 

Page 22

eMIssIon controL 

sYsteM warrantY

california and united states emission control 

defects warranty statement

The California Air Resources Board (herein CARB), the United 

States Environmental Protection Agency (herein EPA), and Harbor 

Freight Tools (herein HFT) are pleased to explain the emission con-

trol system warranty on your 1995 and later Small Off-Road Engine 

(herein engine). In California, the engine must be designed, built 

and equipped to meet the State’s stringent anti-smog standards.  

Elsewhere within the United States, new off-road, spark-ignition 

engines certified for model year 1997 and later, must meet similar 

standards set forth by the EPA.  HFT must warrant the emission 

control system on your engine for the periods of time described 

below, provided there has been no abuse, neglect or improper 

maintenance of your engine.

Your emission control system may include parts such as the 

carburetor or fuel-injection system, and the ignition system. Also 

included  may  be  hoses,  belts,  connectors  and  other  emission-

related assemblies.

Where a warrantable condition exists, HFT will repair your 

engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s warranty coverage

The 1995 and later engines are warranted for two (2) years.  

If any emission-related part on your engine is defective, the part 

will be repaired or replaced by HFT.

Harbor Freight tools emission control defects 

warranty coverage

Engines are warranted for a period of two (2) years relative to 

emission control parts defects, subject to the provisions set forth 

below. If any emission related part on your engine is defective, the 

part will be repaired or replaced by HFT.

 

owner’s warranty responsibilities

As the engine owner, you are responsible for the performance 

• 

of the required maintenance listed in your Owner’s Manual. 

HFT recommends that you retain all receipts covering main-

tenance  on  your  engine,  but  HFT  cannot  deny  warranty 

solely for the lack of receipts or for your failure to ensure the 

performance of all scheduled maintenance.
As the engine owner, you should, however, be aware that 

• 

HFT may deny you warranty coverage if your engine or a part 

has failed due to abuse, neglect, improper maintenance, or 

unapproved modifications.

You are responsible for shipping your engine to a HFT war-

• 

ranty station as soon as a problem exists.  Contact the HFT 

Customer Service department at the number below to make 

shipping  arrangements.   The  warranty  repairs  should  be 

completed in a reasonable amount of time, not to exceed 

30 days.
If  you  have  any  questions  regarding  your  warranty  rights 

and responsibilities, you should contact the Harbor Freight Tools 

Customer Service Department at 1-800-444-3353.

Harbor Freight tools emission control defects 

warranty provisions

Length of coverage

1. 

HfT warrants to a first retail purchaser and each subsequent 

purchaser that the engine is free from defects in materials 

and workmanship that cause the failure of warranted parts 

for a period of two (2) years after the date of delivery to the 

first retail purchaser.

no charge repair or replacement

2. 

Repair or replacement of any warranted part will be performed 

at no charge to the owner if the work is performed through a 

warranty station authorized by HFT.  For emissions warranty 

service, contact the HFT Customer Service Department at 

1-800-444-3353.

consequential damages coverage

3. 

Coverage under this warranty shall also extend to the failure 

of any engine components caused by the failure of any war-

ranted part while it is still covered under this warranty.

coverage exclusions

4. 

Warranty claims shall be filed in accordance with the provi

-

sions of the HFT warranty policy explained in the box at the 

top of the previous page.  HFT shall not be liable for any loss 

of use of the engine, for any alternative usage, for any damage 

to goods, loss of time, or inconvenience.  Warranty coverage 

shall also be excluded for any part which fails, malfunctions, 

or is damaged due to failure to follow the maintenance and 

operating instructions set forth in the Owner’s Manual includ-

ing, but not limited to:

Use of parts which are not authorized by HFT

a) 

Improper installation, adjustment or repair of the engine 

b) 

or of any warranted part unless performed by an autho-

rized warranty center
Failure to follow recommendations on fuel use contained 

c) 

in the Owner’s Manual
Improper or inadequate maintenance of any warranted 

d) 

parts
Repairs performed outside of the authorized warranty 

e) 

service dealers
Alterations by changing, adding to or removing parts 

f) 

from the engine.

service and Maintenance

5. 

Component parts which are not scheduled for replacement 

as required maintenance or are scheduled only for regular 

inspection to the effect of “repair or replace as necessary” 

are warranted for the warranty period. Any warranted part 

which is scheduled for replacement as required maintenance 

is warranted for the period of time up to the first scheduled 

replacement point for that part.  Any replacement part, pro-

vided it is equivalent in durability and performance, may be 

used in performance of maintenance or repairs.  The owner 

is responsible for commissioning a qualified technician/me

-

chanic to perform all required maintenance, as outlined in 

the  Inspection,  Cleaning,  and  Maintenance  section  in  this 

manual.

warranted parts

6. 

Fuel Metering System

1) 

Carburetor and its internal parts.

i) 

Fuel pump (if so equipped).

ii) 

Cold start enrichment system.

iii) 
Air Induction System

2) 

Summary of Contents for 65588
























Reviews: